Download Print this page
Sharp MX-M182 Installation Manual
Sharp MX-M182 Installation Manual

Sharp MX-M182 Installation Manual

Digital multifunctional system
Hide thumbs Also See for MX-M182:

Advertisement

Quick Links

(With optional SPF/RSPF installed)
(With optional SPF/RSPF installed)
MX-M182D
MX-M182
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 2 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[ 3 ] MX-M232D/MX-M202D/MX-M182D/MX-M182 . . . . . . . . . . . . . . 3-1
[ 4 ] AR-SP10/AR-RP10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[ 5 ] AR-D36/AR-D37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[ 6 ] MX-FX13/MX-XB17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[ 7 ] MX-NB12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[ 8 ] MX-TR10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[ 9 ] MX-EB14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] MX-PK10 PS3 EXPANSION KIT . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] CHANGING THE COPY PAPER SIZE IN THE TRAY. . . . . . . . 11-1
[12] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Parts marked with "
" are important for maintaining the safety of the set.
Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

INSTALLATION MANUAL

DIGITAL MULTIFUNCTIONAL
SYSTEM
MODEL
MX-M232D
MX-M202D
CONTENTS
SHARP CORPORATION
CODE : 00ZMXM182/I2E
MX-M182
MX-M182D
MX-M202D
MX-M232D
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

Advertisement

loading

Summary of Contents for Sharp MX-M182

  • Page 1: Installation Manual

    [ 2 ] CONFIGURATION ........2-1 [ 3 ] MX-M232D/MX-M202D/MX-M182D/MX-M182 ....3-1 [ 4 ] AR-SP10/AR-RP10 .
  • Page 2 Disconnect the AC cord before servicing the unit. LASER WAVE - LENGTH : 785 15mm Pulse times : 10.34 s 0.1 s/7mm MX-M182,MX-M182D,MX-M202D 8.665 s 0.1 s/7mm MX-M232D Out put power : Max.0.3mW...
  • Page 3: Note For Servicing

    [1] GENERAL 1. Note for servicing •poorly ventilated Pictogram The label ( ) in the fusing area of the machine indicates the following: : Caution, risk of danger : Caution, hot surface A. Warning for servicing •The fusing area is hot. Exercise care in this area when removing misfed paper.
  • Page 4 D. Note for handling PWB and electronic parts When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity. 1) When in transit or storing, put the parts in an anti-static bag or an anti- static case and do not touch them with bare hands.
  • Page 5 [2] CONFIGURATION 1. System Configurations AR-RP10 AR-SP10 AR-VR7 (MX-M182 is standard) (MX-M182D/M202D/ M232D only) MX-NB12 MX-FX13 MX-M182 MX-M232D MX-M182D MX-M202D MX-XB17 MX-EB14 AR-D36 AR-D37 MX-TR10 MX-US10 MX-PK10 MX-USX1 MX-USX5 MX-US50 MX-USA0 Sharpdesk 10 license kit Sharpdesk 50 license kit Sharpdesk 100 license kit...
  • Page 6 Model MX-M182 MX-M182D/202D/232D Option AR-RP10 Reversing single pass feeder (RSPF) O *1 AR-SP10 Single pass feeder (SPF) O *2 AR-D36 250-sheet paper feed unit AR-D37 2x250-sheet paper feed unit AR-VR7 DOCUMENT COVER O *2 MX-NB12 NETWORK EXPANSION KIT MX-FX13 FACSIMILE EXPANSION KIT...
  • Page 7: Installing Conditions

    [3] MX-M232D/M202D/M182D/M182 1. Installing conditions 3.Installing procedure A.The machine installation A.Developer cartridge installation Do not install your the machine in areas that are: 1) Open the bypass tray, and open the side cover. •damp, humid, or very dusty 2) Open the front cover. •exposed to direct sunlight •Hold the both sides and pull down to open.
  • Page 8: Removal And Storage Of Fixing Screw

    6) Check that two hooks of the developer unit is hooked on the toner C. Set the toner density reference control level cartridge guide, and secure the toner cartridge guide to the 1) With the front cover open, turn ON the machine power and enter developing unit.
  • Page 9 ‘13/Nov [4] AR-SP10/AR-RP10 1. Unpacking 2) Remove the right cabinet. Remove the screws and remove the right cabinet. For unpacking, refer to the figure below. 3) Remove the document glass and the right document glass holder. Remove the screws, remove the document glass from the machine, and then remove the right document glass holder.
  • Page 10 5) Attach the right cabinet. 8) Connect the relay connector. Reattach the right cabinet to its original position and fix it with the Connect the harness of the automatic document feeder to the connec- screws. tor of the machine and tighten the screws on the connector. 9) Remove the filament tape.
  • Page 11 [5] AR-D36/D37 1. Unpacking 2. Installation (AR-D36) Included parts Part name Quantity Screw M4 x 12 (Fixing plate) Fixing plate Paper size label 1) Remove the document cover. Lift the document cover from the machine and tilt it to the rear side to remove it.
  • Page 12 4) Make a hole for connector. 6) Install the machine onto the 250-sheet paper feed unit. Put the machine on the 250-sheet paper feed unit, and fix with the fixing • The machine (1-tray model) plates and the screws. Cut out the portion shown in the illustration with nippers or the like. •...
  • Page 13 • The machine (1-tray model) + 2x250-sheet paper feed unit 7) Remove the connection gear lock. Remove the connection gear lock (with the red tug) after setting. 8) Connect the connector Connect the optional relay harness contained in the 1-tray model (2-tray model) paper feed unit to the PWB of the machine.
  • Page 14 • The machine (2-tray model) + 250-sheet paper feed unit • The machine (2-tray model) + 2x250-sheet paper feed unit Note: When connecting the harness, tighten the earth wire together. • The machine (1-tray model) + 2x250-sheet paper feed unit 9) Remove the cassette packing fixtures.
  • Page 15 [6] MX-FX13/MX-XB17 1. Unpacking 2. Installation (MX-FX13 and MX-XB17) <Before installation> Turn off the main switch of the machine and then remove the power • For improvement of workability, some description in this manual as plug of the machine from the outlet. well as components and accessories may change without prior notice.
  • Page 16 3) Remove the USB devise connector PWB. 5) Install FAX Mounting Unit. <1>Remove one screw. <1>Hook the attaching parts of FAX Mounting Unit onto the machine <2>Remove the USB device connector PWB Unit. frame. <3>Remove the screw and remove the USB devise connector PWB. <2>Secure the unit onto the machine using 4 screws.
  • Page 17 8) Install FAX Expansion Unit. 10) Attach the rear cabinet. <1>Hook the FAX Expansion Unit onto the network frame. Attach the rear cabinet and the rear cabinet cover. Fix it with screws. <2>Secure the unit onto the machine using 4 screws. 11) Remove keyboard back cover.
  • Page 18 13) Attach FAX keyboard. Australia, New Zealand only <1>Connect the machine flat cable to FAX keyboard. A-TICK label attachment. <2>Place the FAX keyboard onto the machine while engaging the pawls. <3>Secure the keyboard using 2 screws. 16) Insert the power plug of the machine to the outlet, and then turn on the main switch of the machine.
  • Page 19 3.Installation (MX-FX13 and MX-NB12) 3) Remove the USB devise connector PWB. <1>Remove one screw. <2>Remove the USB device connector PWB Unit. Turn off the main switch of the machine and then remove the power <3>Remove the screw and remove the USB devise connector PWB. plug of the machine from the outlet.
  • Page 20 6) Install FAX Expansion Unit 8) Cut and remove the cut-out portion from the rear cabinet cover, which is included Network Expansion kit, using a tool such as <1>Hook the attaching parts of FAX Expansion Unit onto the network nippers. Be careful with he tool's direction so that the cut surface frame.
  • Page 21 11) Remove dummy panel. 14) Paste label on the rear cabinet of the machine. After installing FAX Expansion Kit, paste the supplied label on the <1>Unscrew from the dummy panel. position shown in the illustration. <2>Disengage the pawls, and remove the dummy panel from the machine.
  • Page 22 [7] MX-NB12 1. Unpacking 2. Installation 1) Remove the screw. Remove the rear cabinet and the rear cabinet cover. 2) Connect the bundled AC harness to the power PWB of the machine. Note: Connect the connector with the insulation tube of the AC harness to the power PWB of the machine.
  • Page 23 3) Remove one screw, and remove the USB device connector PWB 5) Attach the rear cabinet and the rear cabinet cover. Fix it with on the machine side. screws. Note: Since the power PWB is at the vicinity of the MX-NB12, use enough care when repairing it.
  • Page 24 [8] MX-TR10 1. Unpacking 2-2. Attach the separator motor unit. 1) Connect the connector. <Before installation> 2) Insert the two bosses of the machine into the positioning holes of • For improvement of workability, some description in this manual as the separator motor unit and secure it with the supplied screw.
  • Page 25 2-5. Attach the paper holder arm. 2) Attach the bosses on the rear and front sides of the separator tray to the separator levers on the rear and front sides of the machine. 1) Attach the paper holder arm on the back side of the separator tray. At this time, be careful about the orientation of the paper holder arm.
  • Page 26 2-9. Insert the power cord into the outlet and turn the main switch located on the left side of the machine to the "ON" position. 2-10. Carry out separator unit installation setting. 1) Use the keys on the machine to execute simulation [26-1-1]. 2) Press the [CA] key to exit the simulation.
  • Page 27 [9] MX-EB14 (EXPANSION MEMORY BOARD) 1. Unpacking 3) Attach the Expansion Memory Board to the MCU PWB. Packed part names Quantity EXPANSION MEMORY BOARD EXPANSION MEMORY BOARD (Taiwan, Brazil, South Africa) <Taiwan/Brazil/South Africa> Screw (Taiwan, Brazil, South Africa) Attach the Expansion Memory Board to the MCU PWB, and secure it with a screw.
  • Page 28 [10]MX-PK10 PS3 EXPANSION KIT 1. Unpacking 3. Click the "Product Key Setting". <Parts included> Packed part names Quantity CD-ROM Product key sheet (With Application Number) 2. Installation For installing of the MX-PK10, install the network expansion kit (MX- 4. Enter the product key, and click the "Submit (S)". NB12) in advance.
  • Page 29 C. Turn off/on the power again. D. Visit the web page again, print the "PS Font List" at the "Printer Test Page" screen, check to confirm that the list is normally printed. Note: Very important information is described below. Please keep this description in a safe place where it will not be lost.
  • Page 30 [11]CHANGING THE COPY PAPER SIZE IN THE TRAY If the size of the loaded paper is different from the size shown in the 4) Press the [OK] key. display, follow the steps below to change the paper size setting of the PAPER SIZE SET tray.
  • Page 31: Copier Adjustment

    [12]ADJUSTMENTS 1.Simulations 2.Copier adjustment A. Entering the simulation mode A.Mechanism section Simulation is hereinafter described as SIM. Note:If a jam error or paper empty occurs during copying in the adjustment by the simulation, the image data are not saved, and Perform the following procedure to enter the SIM mode.
  • Page 32 5) Set the OC lead edge position set value (RRC-A) to [1] 10) Set the lead edge void adjustment value (DEN-A)* again. The OC image scanning start position is shifted inside the • 1 step of the set value corresponds to about 0.1mm shift. document edge.
  • Page 33 <Adjustment specification> d. Paper off center adjustment (SIM50-10) Adjustment mode Display Set value Spec value 1) Set a test chart (UKOG-0089CSZZ) on the document table. text range 2) Select a paper feed port and make a copy. Compare the copy and array the test chart.
  • Page 34 (2) Main scanning direction (FR direction) distortion 4) Loosen the set screw of the scanner drive pulley which is not in contact with No. 2/3 mirror base unit positioning plate. balance adjustment 5) Without moving the scanner drive pulley shaft, manually turn the 1) Remove the OC glass and the right cabinet.
  • Page 35: Rear Side

    (3) Main scanning direction (FR direction) distortion 4) Loosen the mirror base drive pulley fixing screw on the front frame side or on the rear frame side. adjustment This adjustment must be performed in the following cases: When La < Lb •...
  • Page 36 <Adjustment specification> 1) Put a scale on the original table as shown below, and make a normal (100%) copy to make a test chart. Note: A judgment must be made with 200mm width, and must not be made with 100mm width. Adjustment mode Display Specifi-...
  • Page 37 4) After completion of warming up, shading is performed and the <Adjustment specification> current off-center adjustment value is displayed on the LCD. Density Display Expo- Sharp Gray Set value mode text sure Chart output range Sim50-12 ORG. CENTER array level...
  • Page 38 LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
  • Page 39 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
  • Page 40 SHARP CORPORATION Business Solutions CS Promotion Center II Yamatokoriyama, Nara 639-1186, Japan First Edition 2011 October Latest Edition 2013 November...

This manual is also suitable for:

Mx-m182dMx-m232dMx-m202d