Related Manuals for Raven AutoBoom Case IH Patriot 250
Summary of Contents for Raven AutoBoom Case IH Patriot 250
- Page 1 Case IH Patriot 250/2240/2250 & New Holland SP2500 (80’- 100’ Booms) AutoBoom® Installation Manual P/N 016-0230-047 Rev. C 01/17 E28493 Copyright 2012, 2013, 2017...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Important Safety Information ................1 Hydraulic ........................... 2 General ....................................... 2 Instructions for Hose Routing ............................2 Electrical ............................ 3 General ....................................... 3 Instructions for Wire Routing ............................3 Chapter 2 Introduction......................5 Preparing for Installation ...................... - Page 4 Table of Contents Chapter 7 Replacement Parts....................33 Valve ............................33 Wheels ............................ 34 Sensors ........................... 34 iiCase IH Patriot 250/2240/2250 & New Holland SP2500 (80’-100’ Booms) AutoBoom® Installation Manual...
-
Page 5: Important Safety Information
AutoBoom® system. • Follow all safety information presented within this manual. • If you require assistance with any portion of the installation or service of your Raven equipment, contact your local Raven dealer for support. • Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. -
Page 6: Hydraulic
HYDRAULIC GENERAL • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized. -
Page 7: Electrical
IMPORTANT SAFETY INFORMATION • Moving linkages, cylinders, articulation joints, attachments • Ground engaging components For hose sections that move during machine operation: • Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or rubbing, especially in articulation and pivot points •... - Page 8 HAPTER Routing should not allow harnesses to: • Hang below the unit • Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris, attachments) • Be placed in areas of or in contact with machine components which develop temperatures higher than the temperature rating of harness components •...
-
Page 9: Chapter 2 Introduction
CHAPTER C H A P T E R 2 Congratulations on your purchase of the Raven AutoBoom system! This system is designed to provide automated boom height adjustment for agricultural equipment. This manual applies to the following machines. For future reference, write your serial number in the space below. -
Page 10: Tools Needed
AutoBoom controller/field computer to ensure the hydraulic system has been installed correctly and air is released from the system. Raven Industries recommends the following best practices when installing the AutoBoom system. • Use part numbers to identify the parts. -
Page 11: Kit Contents
INTRODUCTION At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual. Your feedback will help shape the future of our product documentation and the overall service we provide. - Page 12 HAPTER TABLE 1. Raven CAN UltraGlide Installation Kit (P/N 117-0232-112) or ISO CAN UltraGlide Installation Kit (117-0232-131) Picture Item Description Part Number Qty. Sensors - Right Ultrasonic 063-0130-012 Sensor - Left Ultrasonic 063-0130-014 Sensors - Center Ultrasonic 063-0130-018 Bracket - Sensor Mounting 107-0172-501 Cable - 50’...
- Page 13 INTRODUCTION TABLE 1. Raven CAN UltraGlide Installation Kit (P/N 117-0232-112) or ISO CAN UltraGlide Installation Kit (117-0232-131) Picture Item Description Part Number Qty. Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 Washer - 5/16” Split Lock 313-1000-019 TABLE 2. Hydraulic Installation Kit (P/N 117-0134-075)
- Page 14 HAPTER TABLE 2. Hydraulic Installation Kit (P/N 117-0134-075) Picture Item Description Part Number Qty. Hydraulic Hose - -8 ORFS (F) to -8 ORFS 214-1000-311 (F) 90° - 36” Hydraulic Hose - -6 ORFS (F) 90° to -6 214-1000-494 ORFS (F) - 44” TABLE 3.
- Page 15 INTRODUCTION TABLE 4. Optional Wheel Kit (P/N 117-0138-017) Picture Item Description Part Number Qty. Axle Assembly - AutoBoom 063-0131-567 Bracket - Case IH Weldment 116-0159-544 Wheel 322-0131-008 P/N 016-0230-047 Rev. C...
- Page 16 HAPTER 12Case IH Patriot 250/2240/2250 & New Holland SP2500 (80’-100’ Booms) AutoBoom® Installation Manual...
-
Page 17: Hydraulic System Installation
H YDRAULIC SYSTEM CHAPTER C H A P T E R 3 INSTALLATION WARNING The machine must remain stationary and switched off, with the booms unfolded and supported, during installation or maintenance. CAUTION When installing AutoBoom hydraulics or performing diagnostics, maintenance, or routine service, ensure precautions are taken to prevent any foreign material from being introduced into the machine’s hydraulic system. -
Page 18: Install The Fittings On The Autoboom Valve
HAPTER INSTALL THE FITTINGS ON THE AUTOBOOM VALVE Before mounting the AutoBoom valve on the machine, install the fittings in the appropriate ports of the AutoBoom valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. -
Page 19: Install The Pressure And Tank Hoses
HYDRAULIC SYSTEM INSTALLATION INSTALL THE PRESSURE AND TANK HOSES WARNING Hydraulics are under pressure. Care should always be taken with a system that has been pressurized. When disconnecting or purging hydraulic hoses, be aware that the hydraulic fluid within the machine’s system may be extremely hot and under high pressure. -
Page 20: Install The Left And Right Cylinder Hoses
HAPTER FIGURE 3. Tank Hose Installed 6. Disconnect the machine’s tank hose from the machine’s hydraulic valve. 7. Install a 13/16” ORFS M/M/F swivel run tee fitting (P/N 333-0012-028) in the machine’s tank port. 8. Attach the machine’s tank line to the opposite end of the installed tee fitting. 9. -
Page 21: Install The Left And Right Down Hoses
HYDRAULIC SYSTEM INSTALLATION 6. Connect the straight end of the installed hydraulic hose to the fittings installed in Port RC of the AutoBoom valve. FIGURE 5. Left Cylinder Hose Installed 7. Trace the machine’s left cylinder hose from the rod-end of the left tilt cylinder to the machine’s hydraulic valve. 8. - Page 22 HAPTER 6. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-494) on the 90° end of the installed tee fitting. 7. Connect the straight end of the installed hydraulic hose to the fitting installed in Port LF CYL RTN of the AutoBoom valve.
-
Page 23: Hydraulic Diagram
HYDRAULIC SYSTEM INSTALLATION HYDRAULIC DIAGRAM P/N 016-0230-047 Rev. C... - Page 24 HAPTER 20Case IH Patriot 250/2240/2250 & New Holland SP2500 (80’-100’ Booms) AutoBoom® Installation Manual...
-
Page 25: Chapter 4 Ultrasonic Sensor Installation
INSTALLATION NOTE: For optimal system performance, Raven Industries recommends a five sensor system configuration. If the machine is not already equipped with inner sensors, a dual system upgrade kit (P/N 117-0137-026) is required to complete the five sensor configuration. The dual sensor upgrade kit is sold separately. -
Page 26: Mount The Boom Sensors
HAPTER MOUNT THE BOOM SENSORS WARNING The machine must remain stationary and switched off, with the boom unfolded and supported, during installation or maintenance. FIGURE 2. Sensor Installed on Mounting Bracket 1. Install the left and right ultrasonic sensors (P/N 063-0130-012 and 063-0130-014) on the ultrasonic sensor mounting brackets (P/N 107-0172-501) using four 3/8”-16 x 1-1/4”... -
Page 27: Mount The Center Sensor
ULTRASONIC SENSOR INSTALLATION 3. Mount the right boom sensor assembly on the front of the right outer boom section using two 2-1/16” W x 3” L x 3/8” thread U-bolts (P/N 107-0171-609) and four 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). NOTE: Ensure that the sensor does not contact the inner boom section when the boom is folded in toward the cab. -
Page 28: Connect The Sensor Cables
HAPTER CONNECT THE SENSOR CABLES 1. Connect the left sensor cable (P/N 115-0230-050) to the connector on the left sensor. 2. Route the left sensor cable toward the AutoBoom valve. 3. Loop and tie-off any excess cable, allowing enough cable for boom folding and extension. 4. -
Page 29: Gauge Wheel Installation (Optional)
G AUGE WHEEL INSTALLATION CHAPTER C H A P T E R 5 (OPTIONAL) GAUGE WHEEL MOUNTING LOCATIONS Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms. - Page 30 HAPTER 4. Mount the right wheel receiver bracket (P/N 116-0159-544) to the front of the right boom using four U-bolts, and eight flanged lock nuts. 5. Insert the right wheel axle into the right wheel receiver bracket, positioning it so that the bottom of the wheel touches the ground (or nearly so) and the wheel faces away from the machine.
-
Page 31: Wiring Installation
W IRING INSTALLATION CHAPTER C H A P T E R 6 WIRING CONNECTIONS CAUTION Always connect the power cable as the last step in the wiring process and verify that the power leads are connected with the correct polarity. Reversing power leads can cause severe damage to the equipment. -
Page 32: Connect The Harness To The Autoboom Valve
HAPTER CONNECT THE HARNESS TO THE AUTOBOOM VALVE FIGURE 2. AutoBoom Harness Connected to Valve 1. Locate the LEFT PRESS and RIGHT PRESS connectors on the harness cable (P/N 115-0230-073). 2. Route the connectors to the AutoBoom valve (P/N 063-0131-124). 3. -
Page 33: Connect The Harness To The Can Controls
WIRING INSTALLATION CONNECT THE HARNESS TO THE CAN CONTROLS FIGURE 3. AutoBoom Harness Cable Installed 1. Locate the machine’s harness cable bulkhead connection in the upper-left corner of the center boom section. 2. Disconnect the machine’s cable from the bulkhead connector. FIGURE 4. -
Page 34: Connect The Left And Right Centering Sensors - If Applicable
HAPTER FIGURE 5. Machine’s Existing CAN Connection 4. Locate and disconnect the machine’s existing 4-pin CAN connection in front of the transducer on the center boom section. NOTE: The CAN connection may or may not have a terminator installed. FIGURE 6. AutoBoom Harness Installed on Machine’s CAN Connections 5. - Page 35 WIRING INSTALLATION FIGURE 7. Extension Cable Installed on Sensor 1. Install the male end of the 2-pin weatherpack 63” extension cable (P/N 115-0172-147) on the left centering sensor cable located on top of the left boom, near the center rack. FIGURE 8.
-
Page 36: Connect The Power Leads
HAPTER CONNECT THE POWER LEADS FIGURE 9. Machine’s Existing Power Connection 1. Locate the machine’s existing 2-pin power connection in front of the pressure transducer. 2. Remove the dust cap from the machine’s power connection. FIGURE 10. AutoBoom Harness Cable Power Connection 3. - Page 37 R EPLACEMENT PARTS CHAPTER C H A P T E R 7 This section contains replacement part diagrams for the UltraGlide AutoBoom system. Refer to these diagrams when calling to request replacement parts. VALVE P/N 016-0230-047 Rev. C...
- Page 38 HAPTER WHEELS SENSORS 34Case IH Patriot 250/2240/2250 & New Holland SP2500 (80’-100’ Booms) AutoBoom® Installation Manual...
- Page 39 Index Electrical Safety Sensor Installation Mounting the Center Sensor Gauge Wheel Installation (Optional) Gauge Wheel Mounting Locations Tools Needed Mounting the Gauge Wheels Ultrasonic Sensor Installation Connecting the Sensor Cables Hydraulic Fittings Mounting the Boom Sensors Hydraulic Safety Boom Sensor Mounting Locations 21 Hydraulic System Mount the Boom Sensors 22 Installing the Fittings on the AutoBoom Valve...
- Page 40 Index 36Case IH Patriot 250/2240/2250 & New Holland SP2500 (80’-100’ Booms) AutoBoom® Installation Manual...
- Page 41 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
- Page 42 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.