Raven CR7 Quick Start Manual
Hide thumbs
Also See for CR7:
- Operation manual (71 pages) ,
- User manual (34 pages) ,
- Calibration manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Raven CR7
Summary of Contents for Raven CR7
- Page 1 CR7/CR12 QUICK START GUIDE 116-8000-017 REV. B2 User manual...
- Page 2 | CR7/CR12 | QUICK START GUIDE PAGE 2/35 | User manual | 116-8000-017 | Rev. B2...
-
Page 3: Disclaimer
It is strictly prohibited to use the CR7/CR12 system on public roads. • It is strictly prohibited to leave a driving vehicle unattended when the CR7/CR12 system is switched on. The • driver is always responsible for the direction and course of the vehicle. -
Page 4: Table Of Contents
INDEX | CR7/CR12 | QUICK START GUIDE INDEX DISCLAIMER ........................................3 INDEX ...........................................4 HOW TO CHANGE BETWEEN DIFFERENT TRACTORS .......................5 COUPLING IMPLEMENT ..................................7 DRIVE DIRECTION ....................................9 NEW FIELD + CREATE NEW LINE ..............................10 ADD SECOND LINE OR ADD MULTIPLE LINES .......................... 13 LOAD FIELD ...................................... -
Page 5: How To Change Between Different Tractors
HOW TO CHANGE BETWEEN DIFFERENT TRACTORS | CR7/CR12 | QUICK START GUIDE 1 HOW TO CHANGE BETWEEN DIFFERENT TRACTORS Beschrijving Afbeelding If the tractor profile has to be changed. Open the UT with the the UT widget. Press the gear icon. - Page 6 HOW TO CHANGE BETWEEN DIFFERENT TRACTORS | CR7/CR12 | QUICK START GUIDE Press settings (the gear icon at the bottom left), and then press Machine (the tractor icon). Press the configured tractor. A different type of machine must also be loaded inside the machine garage.
-
Page 7: Coupling Implement
SELECT IMPLEMENT | CR7/CR12 | QUICK START GUIDE 2 SELECT IMPLEMENT Afbeelding Beschrijving Press settings (the gear icon at the bottom left), and then press Machine (the tractor icon). Press the configured tractor. A different type of machine must also be loaded inside the machine garage. - Page 8 SELECT IMPLEMENT | CR7/CR12 | QUICK START GUIDE Note: Currently the “spreader” is mounted with a working width of 16 meters devided in one section. Working width is the distance that will be created between the various guidance lines. Press the green checkmark finish the configuration.
-
Page 9: Drive Direction
DRIVE DIRECTION | CR7/CR12 | QUICK START GUIDE 3 DRIVE DIRECTION Beschrijving Afbeelding It is possible that the direction is not recognized correctly (forwards/backwards). You can recognize it by the white arrow that appears in the middle of the screen. -
Page 10: New Field + Create New Line
NEW FIELD + CREATE NEW LINE | CR7/CR12 | QUICK START GUIDE 4 NEW FIELD + CREATE NEW LINE Beschrijving Afbeelding Press on icon: “New field + New line”. When the list of fields is open, first close it. After this the icon will appear. - Page 11 NEW FIELD + CREATE NEW LINE | CR7/CR12 | QUICK START GUIDE Note: Now press AB line, to create an A-B line. Press A+ to enter an existing direction. Press on Curve when you want to create a bend or pendulum.
- Page 12 NEW FIELD + CREATE NEW LINE | CR7/CR12 | QUICK START GUIDE It is still possible to name the A-B line, making it easy to find and load later. Change the position of the line (shift or center the line).
-
Page 13: Add Second Line Or Add Multiple Lines
ADD SECOND LINE OR ADD MULTIPLE LINES | CR7/CR12 | QUICK START GUIDE 5 ADD SECOND LINE OR ADD MULTIPLE LINES Beschrijving Afbeelding Open the tab "lines" (press the arrow on the right, then the tab opens). Deactivate the loaded line by pressing the X. -
Page 14: Load Field
LOAD FIELD | CR7/CR12 | QUICK START GUIDE 6 LOAD FIELD Beschrijving Afbeelding Simply press an existing field on the map in the background. Open via the overview of all fields and press the desired field. Tip! By pressing the filter, the order of the fields can be changed. - Page 15 LOAD FIELD | CR7/CR12 | QUICK START GUIDE Note: An overview of the tractor and the attached implement is provided. Is the implement correct? Then move • Is the implent wrong? Then go back • to machine garage. (Chapter 2).
- Page 16 LOAD FIELD | CR7/CR12 | QUICK START GUIDE Select the region you want to base your guidance lines off. PAGE 16/35 | User manual | 116-8000-017 | Rev. B2...
-
Page 17: Switching Between The Lines
SWITCHING BETWEEN THE LINES | CR7/CR12 | QUICK START GUIDE 7 SWITCHING BETWEEN THE LINES Beschrijving Afbeelding To switch between existing operation lines (e.g. from edge line to headland line) Press the line icon. And then on ‘’load’’. Select the guidance line. -
Page 18: Shift The Position Of The Line
SHIFT THE POSITION OF THE LINE | CR7/CR12 | QUICK START GUIDE 8 SHIFT THE POSITION OF THE LINE Beschrijving Afbeelding Two ways to change the line position. 1. Shift with a set distance. Left or right (example 10cm). 2. Line centering: guidance line will placed directly underneath the machine. -
Page 19: New Field: Record Field Boundary
NEW FIELD: RECORD FIELD BOUNDARY | CR7/CR12 | QUICK START GUIDE 9 NEW FIELD: RECORD FIELD BOUNDARY Beschrijving Afbeelding Press "fields". Press "+ ". Give the field a name and confirm this. Press "record field boundary". PAGE 19/35 | User manual | 116-8000-017 | Rev. B2... -
Page 20: Record Field Boundery
RECORD FIELD BOUNDERY | CR7/CR12 | QUICK START GUIDE 10 RECORD FIELD BOUNDERY Beschrijving Afbeelding Choose on which side of the machine the field boundary should be recorded. The size of the implement is used as guidance width. Is the right implement mounted? See chapter 2. - Page 21 RECORD FIELD BOUNDERY | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Turn the tractor in the other direction. Now press "Add corner flag” again. There's a double flag in the corner now. By using 2 corners flags for each corner of the field the direction of the boundary will be 100% accurate.
- Page 22 RECORD FIELD BOUNDERY | CR7/CR12 | QUICK START GUIDE Besschrijving Afbeelding When a side of a field contains a curve: Start by pressing "Add corner flag". This is the beginning of the line. Now press "pause". If the recoding is paused nothing will be...
- Page 23 RECORD FIELD BOUNDERY | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Continue to the end point. Always turn off automatic closing field (remove check mark) ! At the end of the line, add another "corner flag”. Field boundary is set, now press the icon "stop".
- Page 24 RECORD FIELD BOUNDERY | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Confirm the end of the recording. With the green check mark you confirm the created field and name of the field. Continue to pre-planning. Pre-planning enables you to adjust the field boundary.
-
Page 25: Pre-Planning Operation
PRE-PLANNING OPERATION | CR7/CR12 | QUICK START GUIDE 11 PRE-PLANNING OPERATION Beschrijving Afbeelding You will be automatically redirected to the next page when the field boundary is created When a Shapefile is imported, press the imported field and then “pre-planning”. - Page 26 | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Select which lines should be made straight or stay contour lines. Lines D, H and J will be made straight and F and B remain contour lines. Note: PAGE 26/35 | User manual | 116-8000-017 | Rev. B2...
-
Page 27: Operations
OPERATIONS | CR7/CR12 | QUICK START GUIDE 12 OPERATIONS Beschrijving Afbeelding You will now be automatically redirected to the operation when pre-planning is complete. When a new operation plan needs to be created, press the “right arrow”. Now press "operation planning". - Page 28 OPERATIONS | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Press tramline configuration to add and configure the tramlines. S1: Number of lines from field boundary to first tramline. W1: More or less space at the tramline, on the left W2: More or less space at the tramline, on the right.
- Page 29 OPERATIONS | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Press "Create". The region that is selected will automatically be your main line. The set pattern is filled in over the entire field. A negative distance from the field boundary can be added when the pattern has to be started to the left or right of the line.
-
Page 30: Edit Regions
EDIT REGIONS | CR7/CR12 | QUICK START GUIDE 13 EDIT REGIONS Beschrijving Afbeelding Adjustments can also be made to the other regions, press the adjust icon. Direction: The headlands can be made on the other side of the region. Distance to field boundary: extra distance between the first guidance line and the field boundary. - Page 31 EDIT REGIONS | CR7/CR12 | QUICK START GUIDE Beschrijving Afbeelding Green check mark to confirm the operation. The other regions that are selected will immediately receive the same tramline settings. You can also make manual adjustments yourself. Press the green check mark to confirm Green check mark to confirm.
-
Page 32: New Task + Start Operation
NEW TASK + START OPERATION | CR7/CR12 | QUICK START GUIDE 14 NEW TASK + START OPERATION Beschrijving Afbeelding Now press "New job" When an operation needs to be loaded: press the bar under "Select operation", the desired operation can be chosen. -
Page 33: Task + Reload Operation
TASK + RELOAD OPERATION | CR7/CR12 | QUICK START GUIDE 15 TASK + RELOAD OPERATION Beschrijving Afbeelding Press the desired field. Press one of the tasks you want to load or the operation you want. The operation can be resumed. -
Page 34: Example Of Buiding A Boundery
EXAMPLE OF BUIDING A BOUNDERY | CR7/CR12 | QUICK START GUIDE 16 EXAMPLE OF BUIDING A BOUNDERY PAGE 34/35 | User manual | 116-8000-017 | Rev. B2... - Page 35 EXAMPLE OF BUIDING A BOUNDERY | CR7/CR12 | QUICK START GUIDE PAGE 35/35 | User manual | 116-8000-017 | Rev. B2...