Related Manuals for Raven Case IH SmartTrax SPX 3230
Summary of Contents for Raven Case IH SmartTrax SPX 3230
- Page 1 Case IH SPX 3230, 3320, and 3330 SmartTrax™ Installation Manual P/N 016-5032-081 Rev A 06/15 E22879 Copyright 2014...
- Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Important Safety Information..........1 Hydraulic Safety ........................2 Electrical Safety ........................2 Chapter 2 Introduction................3 Preparing for Installation ......................3 Recommendations ......................4 Point of Reference ....................... 4 Kit Contents ..........................5 Chapter 3 Hydraulic System Installation.......... - Page 4 Table of Contents Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual...
-
Page 5: Important Safety Information
• Follow all safety information presented within this manual. • If you require assistance with any portion of the installation or service of your Raven equipment, contact your local Raven dealer for support. • Follow all safety labels affixed to the SmarTrax system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. -
Page 6: Hydraulic Safety
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized. -
Page 7: Introduction
I ntroduction CHAPTER C h a p t e r 2 Congratulations on your purchase of the SmarTrax system! This system is designed to provide cutting-edge, hands-free steering of the machine via Global Positioning System (GPS) coordinates. This manual applies to the following machines: MAKE: Case IH MODEL: SPX 3230, 3320, and 3330 Case IH SPX 3320... -
Page 8: Recommendations
The instructions in this manual assume that you are standing behind the machine, looking toward the cab. At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual. -
Page 9: Kit Contents
SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer. Note: The SmarTrax node (P/N 063-0173-228) is sold separately. Contact your local Raven dealer for ordering information. Case IH Patriot 3320/3230/3330 SmarTrax Installation Kit (P/N 117-5032-081) TABLE 1. - Page 10 Chapter 2 Case IH Patriot 3320/3230/3330 SmarTrax Installation Kit (P/N 117-5032-081) TABLE 1. Picture Item Description Part Number Qty. Screw - 1/4”-20 x 2” Socket Head 311-0050-109 Bolt - 5/16” Hex Head 311-0052-104 Nut - 1/4”-20 Hex 312-1001-074 Washer - 1/4” Split Lock 313-1000-016 Washer - 5/16”...
- Page 11 Introduction Hydraulic Installation Kit (P/N 117-0199-081) TABLE 2. Picture Item Description Part Number Qty. Fitting - -6 SAE O-Ring Plug 333-0012-104 Fitting - -6 ORFS (M) to -8 SAE O-Ring (M) 333-0012-199 Straight Adapter Fitting - -6 ORFS (M) to -10 SAE O-Ring (M) 333-0012-233 Straight Adapter Hydraulic Hose - -6 ORFS (F) 90°...
- Page 12 Chapter 2 Node Mounting Kit (P/N 117-0197-078) TABLE 3. Picture Item Description Part Number Qty. Nut - 1/4”-20 UNC Nylon Insert Lock 312-4000-057 Washer - .312 ID x .734 OD x .065 Thick 312-2300-011 Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual...
-
Page 13: Hydraulic System Installation
H ydraulic System CHAPTER C h a p t e r 3 Installation WARNING Hydraulics are under pressure. Care should always be taken with a system that has been pressurized. Before beginning the SmarTrax hydraulic installation, turn off the machine and relieve pressure by turning the steering wheel left and right. -
Page 14: Install Fittings On The Smartrax Valve
Chapter 3 NOTICE The appearance of the SmarTrax hydraulic valve may vary slightly from the images contained in this manual. However, the fittings, hose connections, and cable connections remain the same. Install Fittings on the SmarTrax Valve Before mounting the SmarTrax valve (P/N 334-0003-088) on the machine, install the proper fittings in the valve. -
Page 15: Install Fittings On The Flow Switch
Hydraulic System Installation Install Fittings on the Flow Switch Fittings Installed on the Flow Switch FIGURE 2. Install a -6 ORFS (M) to -6 SAE O-ring (M) straight adapter fitting (P/N 333-0012-084) in Ports A2 and B2 of the flow switch (P/N 334-003-085). Install the pressure transducers in Ports A1 and B1 of the flow switch. -
Page 16: Install The Pressure Hose
Chapter 3 SmarTrax Valve Installed on Mounting Plate FIGURE 4. Mount the SmarTrax valve (P/N 334-0003-088) to the hydraulic valve mounting bracket (P/N 107-0171-705) using four 5/16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). Mount the flow switch (P/N 334-0003-085) to the valve mounting bracket using two 1/4”-20 x 2” screws (P/N 311-0050-109), two 1/4”... -
Page 17: Install The Tank Hose
Hydraulic System Installation Pressure Hose Installed FIGURE 6. Install a -6 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-069) on the steel pressure line. Connect the machine’s pressure hose to the opposite end of the installed tee fitting. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-318) on the 90° end of the installed tee fitting. -
Page 18: Install The Left And Right Steering Hoses
Chapter 3 Install the -8 end of the supplied hydraulic hose (P/N 214-1000-630) on the 90° end of the installed tee fitting. Connect the other end of the installed hydraulic hose to Port T of the SmarTrax valve. Install the Left and Right Steering Hoses Locate and disconnect the machine’s left steering hose from the left steering cylinder. - Page 19 Hydraulic System Installation Installed Right Steering Hose FIGURE 9. Right Steering Hose Left Steering Hose Locate and disconnect the machine’s right steering hose from the right steering cylinder. Install a -6 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-069) in the open steering cylinder port. Connect the machine’s right steering hose to the opposite end of the installed tee fitting.
-
Page 20: Hydraulic System Diagram
Chapter 3 Hydraulic System Diagram Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual... -
Page 21: Cab Component Installation
C ab Component CHAPTER C h a p t e r 4 Installation Install the SmarTrax Node Mount the SmarTrax Node Node Mounted to the Mounting Plate FIGURE 1. Mount the SmarTrax node (P/N 063-0173-228) to the node mounting plate (P/N 107-0171-924) using three 1/4”-20 x 7/8”... - Page 22 Chapter 4 Standoffs Installed on Mounting Plate FIGURE 2. Remove the nuts from the machine’s mounting plate. Note: The machine’s mounting plate is located behind the operator’s seat. Screw the M6 x 40 mm M/F to 13mm hex standoffs (P/N 305-8000-008) onto the two studs of the machine’s mounting plate.
-
Page 23: Node Mounting Locations
Cab Component Installation Node Mounting Locations Node Mounting FIGURE 4. Direction Arrows Any two arrows must be parallel with level ground Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. - Page 24 Chapter 4 Install the two large, rectangular connectors of the node cable (P/N 115-4001-110) into the correct ports of the node, tightening the bolts on the harness connectors to secure the connections. CAN Connector Installed on Machine’s CAN System FIGURE 6. Connect the CAN connector to the machine’s existing CAN system.
-
Page 25: Install The Valve Harness
Cab Component Installation DGPS OUT Connected to Console Receiver Connection FIGURE 8. Console Console Receiver Cable Connection DGPS Out (Node Cable Connection) Connect the DGPS OUT connector to the Viper Pro or Envizio Pro receiver connection. Install the Valve Harness Valve Cable Routed Through Access Point FIGURE 9. -
Page 26: Install The Foot Switch
Chapter 4 Valve Harness Connected to Flow Switch FIGURE 10. Plug the PS1 and PS2 connectors from the valve cable into the pressure transducers installed on the flow switch (P/N 334-0003-085). Note: These connections can be plugged into either transducer. Plug the VALVE connector from the valve cable into the open port at the end of the SmarTrax valve (P/N 334-0003-088). -
Page 27: System Diagrams
Cab Component Installation System Diagrams Node Wiring Diagram Manual No. 016-5032-081 Rev. A... - Page 28 Chapter 4 Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual...
- Page 29 Cab Component Installation Manual No. 016-5032-081 Rev. A...
- Page 30 Chapter 4 Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual...
-
Page 31: Startup Procedures
S tartup Procedures CHAPTER C h a p t e r 5 WARNING When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. WARNING Do not use hands to check for leaks. -
Page 32: Verify The Hydraulic System Installation
Note: If there are issues with the SmarTrax system, turn off the machine and correct them immediately. For additional assistance, contact your local Raven dealer. Calibrate the SmarTrax System Refer to the SmarTrax & SmartSteer Calibration and Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. - Page 33 Index Cab Component Installation Installing the Foot Switch 22 Installing the Node Harness 19 Installing the SmarTrax Node 17 Mounting the SmarTrax Node 17 Node Mounting Locations 19 Installing the Valve Harness 21 System Diagrams 23 Hydraulic System Installation Hydraulic System Diagram 16 Installing Fittings on the Flow Switch 11 Installing Fittings on the SmarTrax Valve 10 Installing the Left and Right Steering Hoses 14...
- Page 34 Index Case IH SPX 3230, 3320, and 3330 SmarTrax™ Installation Manual...
- Page 35 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
- Page 36 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.