1. Manuals
  2. Brands
  3. Raven Manuals
  4. Farm Equipment
  5. AutoBoom
  6. Installation manual

Raven AutoBoom Installation Manual

For case ih 3150; case ih 3185 tyler patriot open center
Hide thumbs Also See for AutoBoom:
Table of Contents

Advertisement

Quick Links

Download this manual
Case IH 3150/3185 Pre-2002 Tyler
Patriot Open Center
AutoBoom™ Installation Manual
P/N 016-0230-005 Rev E
09/15
E18127
Copyright 2011, 2015

Advertisement

Table of Contents
loading

Related Manuals for Raven AutoBoom

Summary of Contents for Raven AutoBoom

  • Page 1 Case IH 3150/3185 Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual P/N 016-0230-005 Rev E 09/15 E18127 Copyright 2011, 2015...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.

  • Page 3: Table Of Contents

    PowerGlide Plus Kit Contents ....................7 Install the PowerGlide Plus Hydraulic System ............... 12 Remove the Orifice Fittings ....................12 Install Fittings on the AutoBoom Valve ................15 Mount the AutoBoom Valve ....................16 Install the Pressure Hoses ....................17 Install the Tank Hoses - CaseIH and Patriot 1997 &...
  • Page 4 Gen I Cabling ........................50 Gen II Cabling ........................51 Chapter 5 Replacement Parts ............... 53 Valve Blocks ..........................53 Valve Block Replacement Parts ..................53 Wheels ........................... 54 Sensors ..........................54 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 5: Important Safety Information

    Raven dealer for support. • Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact your local Raven dealer.

  • Page 6: Hydraulic Safety

    Chapter 1 WARNING • When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear, in case a hose has not been properly tightened. • The machine must remain stationary and switched off, with the booms unfolded and supported while installation or maintenance is conducted.

  • Page 7: Introduction

    Be sure to identify which system you have and follow only the instructions for that system. Preparing for Installation Before installing AutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine turned off for the duration of the installation process.

  • Page 8: Recommendations

    Recommendations Raven Industries recommends the following best practices before installing or operating the AutoBoom system for the first time, at the start of the season, or when moving the AutoBoom system to another machine: • Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic...
  • Page 9 Introduction SAE O-ring fitting JIC fitting (M) ORFS fitting Manual No. 016-0230-005...
  • Page 10 Chapter 2 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 11: Powerglide Plus

    PowerGlide Plus Kit Contents This section contains a list of the components that are included in the PowerGlide Plus AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 12 (M) Straight Adapter Fitting - 9/16” JIC (M) to 3/4” SAE O-Ring (M) 333-0012-046 Straight Adapter Fitting - 3/4” SAE O-Ring (M) to 3/4” JIC (M) 333-0012-093 Straight Adapter Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 13 PowerGlide Plus Hydraulic Kit (P/N 117-0134-005) TABLE 2. Picture Item Description Part Number Qty. Fitting - 1-1/16” JIC M/F 90° Swivel Elbow 333-0012-099 Fitting - 1-1/16” JIC M/M/F Swivel Run Tee 333-0012-109 Fitting - 3/8” NPT (M) to 9/16” JIC (M) 333-0012-123 Straight Adapter Fitting - 9/16”...
  • Page 14 Gen I PowerGlide Plus Wiring Kit (P/N 117-0137-023) TABLE 4. Picture Item Description Part Number Qty. Not Pictured Manual - AutoBoom Calibration & Operation 016-0130-062 Node - PowerGlide Plus AutoBoom 063-0130-010 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 15 Important: In addition to the Gen II wiring kit components listed above, an implement extension tee cable is required for the operation of the PowerGlide Plus AutoBoom system. For available cables and ordering information, contact your local Raven dealer. Manual No. 016-0230-005...

  • Page 16: Install The Powerglide Plus Hydraulic System

    Remove the Orifice Fittings Before populating the hydraulic fittings on the AutoBoom valve, it is necessary to remove orifice fittings from the valve in the PowerGlide Plus system. Failure to remove these fittings from the valve will restrict the down speed of the booms when the system is enabled.
  • Page 17 FIGURE 1. Port 3B Port 3A Locate Ports 3A and 3B on the AutoBoom valve (P/N 063-0131-126). Coil Removed from the AutoBoom Valve FIGURE 2. Remove the coils from the solenoids near Ports 3A and 3B to gain easy access to those ports.
  • Page 18 Remove the orifice fittings from Ports 3A and 3B. Important: Tip the AutoBoom valve on its side and use the Allen wrench to remove the orifice from the cavity, taking care not to let the fitting fall into the valve.

  • Page 19: Install Fittings On The Autoboom Valve

    PowerGlide Plus Install Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the proper fittings on the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. WARNING...

  • Page 20: Mount The Autoboom Valve

    AutoBoom Valve Mounted on the Valve Mounting Plate FIGURE 7. Secure the AutoBoom valve (P/N 063-0131-126) to the mounting plate (P/N 107-0171-802) using four 5/16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). AutoBoom Valve Mounted on the Sprayer FIGURE 8.

  • Page 21: Install The Pressure Hoses

    Connect the end of the pressure line to the fitting installed in Port EF of the AutoBoom valve. Connect the straight end of the supplied hydraulic hose (P/N 214-1000-302) to the machine’s steel line. Connect the 90° end of the installed hose to the fitting installed in Port P of the AutoBoom valve. Manual No. 016-0230-005...

  • Page 22: Install The Tank Hoses - Caseih And Patriot 1997 & Newer Only

    Connect the straight end of the supplied hydraulic hose (P/N 214-1000-304) to the installed 90° elbow fitting. Connect the 90° end of the hydraulic hose to the fitting installed in Port T of the AutoBoom valve. Install the Tank Hoses - Tyler Patriot 1996 & Older Only Tank Hose Installed - Tyler Patriot 1996 &...

  • Page 23: Install Left And Right Cylinder Hoses

    Disconnect the cylinder hoses from the rod-ends of the machine’s tilt cylinders. Route the right cylinder hose back to the AutoBoom valve and connect it to the fitting installed in Port RV. Route the left cylinder hose back to the AutoBoom valve and connect it to Port LV.

  • Page 24: Install The Down Hoses

    Disconnect the hose from the base-end of the machine’s left tilt cylinder. Route the hose to the AutoBoom valve and connect it to the fitting installed on the 90° end of the tee fitting in the LF CYL RTN Port.

  • Page 25: Powerglide Plus Hydraulic Schematic

    PowerGlide Plus PowerGlide Plus Hydraulic Schematic Manual No. 016-0230-005...

  • Page 26: Install The Gauge Wheels

    Secure the gauge wheel assembly in the wheel mounting bracket by installing two 1/2”-13 x 1-1/2” SS hex bolts (P/N 311-0058-186) and two 1/2” zinc hex nuts (P/N 312-1001-043). Repeat the steps above to install the right wheel. Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 27: Install The Powerglide Plus Wiring

    Install the AutoBoom Node PowerGlide Plus AutoBoom Node Installed FIGURE 16. Mount the AutoBoom node (P/N 063-0130-010) to the valve mounting plate using three 3/8”-16 x 1-1/4” zinc hex bolts (P/N 311-0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). Note: Position the node so that the cable connectors face down.

  • Page 28: Connect The Harness To The Boom Function Controls

    Chapter 3 Connect the Harness to the Boom Function Controls Locate the Left Press and Right Press connectors on the AutoBoom harness cable (P/N 115-0230-045 or 115-0230-085). Route the connectors to the AutoBoom valve (P/N 063-0131-125). Connect the Left Press connector to Port G1 on the AutoBoom valve.

  • Page 29: Connect The Harness Cable To The Controller Cable - Gen I Cable Only

    Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-021). Note: The AutoBoom controller should be mounted in the machine’s cab so that the machine’s operator has easy access to it. Connect the Field Computer (If Applicable) Refer to the Installation &...

  • Page 30: Powerglide Plus Wiring Schematic

    Chapter 3 PowerGlide Plus Wiring Schematic Gen I Cabling Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 31: Gen Ii Cabling

    PowerGlide Plus Gen II Cabling Manual No. 016-0230-005...
  • Page 32 Chapter 3 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 33: Ultraglide

    This section contains a list of the components that are included in the UltraGlide AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 34 Hydraulic Kit (P/N 117-0134-005) TABLE 2. Picture Item Description Part Number Qty. Fitting - 3/4” JIC M/M/F Swivel Run Tee 333-0012-039 Fitting - 9/16” JIC M/M/F Swivel Run Tee 333-0012-043 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 35 UltraGlide Hydraulic Kit (P/N 117-0134-005) TABLE 2. Picture Item Description Part Number Qty. Fitting - 7/16” JIC (M) to 9/16” SAE O-Ring 333-0012-044 (M) Straight Adapter Fitting - 9/16” JIC (M) to 9/16” SAE O-Ring 333-0012-045 (M) Straight Adapter Fitting - 9/16” JIC (M) to 3/4” SAE O-Ring (M) 333-0012-046 Straight Adapter Fitting - 3/4”...
  • Page 36 Washer - 5/16” Zinc Flat 313-2300-012 Optional Wheel Kit (P/N 117-0133-005) TABLE 4. Picture Item Description Part Number Qty. Axle Assembly - Right Offset Cushioned 063-0131-589 Axle Assembly - Left Offset Cushioned 063-0131-591 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 37 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 Gen I UltraGlide Wiring Kit (P/N 117-0137-024) TABLE 5. Picture Item Description Part Number Qty. Not Pictured Manual - AutoBoom Calibration & Operation 016-0130-062 Node - UltraGlide AutoBoom 063-0130-013 Cable - Sensor 115-0171-527 Manual No. 016-0230-005...
  • Page 38 Important: In addition to the Gen II wiring kit components listed above, an implement extension tee cable is required for the operation of the UltraGlide AutoBoom system. For available cables and ordering information, contact your local Raven dealer. Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 39: Install The Ultraglide Hydraulic System

    Install the UltraGlide Hydraulic System Install Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the proper fittings on the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.

  • Page 40: Mount The Autoboom Valve

    AutoBoom Valve Mounted on the Valve Mounting Plate FIGURE 1. Secure the AutoBoom valve (P/N 063-0131-126) to the mounting plate (P/N 107-0171-802) using four 5/16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). AutoBoom Valve Mounted on the Sprayer FIGURE 2.

  • Page 41: Install The Pressure Hoses

    Connect the end of the pressure line to the fitting installed in Port EF of the AutoBoom valve. Connect the straight end of the supplied hydraulic hose (P/N 214-1000-302) to the machine’s steel line. Connect the 90° end of the installed hose to the fitting installed in Port P of the AutoBoom valve. Manual No. 016-0230-005...

  • Page 42: Install The Tank Hoses - Caseih And Patriot 1997 & Newer Only

    Connect the straight end of the supplied hydraulic hose (P/N 214-1000-304) to the installed 90° elbow fitting. Connect the 90° end of the hydraulic hose to the fitting installed in Port T of the AutoBoom valve. Install the Tank Hoses - Tyler Patriot 1996 & Older Only Tank Hose Installed - Tyler Patriot 1996 &...

  • Page 43: Install Left And Right Cylinder Hoses

    Disconnect the cylinder hoses from the rod-end of the machine’s tilt cylinders. Route the right cylinder hose back to the AutoBoom valve and connect it to the fitting installed in Port RV. Route the left cylinder hose back to the AutoBoom valve and connect it to Port LV.

  • Page 44: Install The Down Hoses

    Disconnect the hose from the base-end of the machine’s left tilt cylinder. Route the hose to the AutoBoom valve and connect it to the fitting installed on the 90° end of the tee fitting in the LF CYL RTN Port.

  • Page 45: Ultraglide Hydraulic Schematic

    UltraGlide UltraGlide Hydraulic Schematic Manual No. 016-0230-005...

  • Page 46: Install The Ultraglide Sensors

    FIGURE 9. Mount the Boom Sensors WARNING The machine must remain stationary and switched off, with the boom unfolded and supported, during installation or maintenance. Mounted Boom Sensor FIGURE 10. Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 47: Mount The Center Rack Sensor

    Loop and tie-off any excess cable, while allowing enough cable for boom folding and extension. Repeat the steps above to connect the remaining boom sensor cables. Note: The sensor cables will be connected to the AutoBoom system in the wiring phase of installation. Manual No. 016-0230-005...

  • Page 48: Install The Gauge Wheels - Optional

    Secure the gauge wheel assembly in the wheel mounting bracket by installing two 1/2”-13 x 1-1/2” SS hex bolts (P/N 311-0058-186) and two 1/2” zinc hex nuts (P/N 312-1001-043). Repeat the steps above to install the right wheel. Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 49: Install The Ultraglide Wiring

    Install the AutoBoom Node UltraGlide AutoBoom Node Installed FIGURE 13. Mount the AutoBoom node (P/N 063-0130-013) to the valve mounting plate using three 3/8”-16 x 1-1/4” zinc hex bolts (P/N 311-0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). Note: Position the node so that the cable connectors face down.

  • Page 50: Connect The Harness To The Boom Function Controls

    Chapter 4 Connect the Harness to the Boom Function Controls Locate the Left Press and Right Press connectors on the AutoBoom harness cable (P/N 115-0230-045 or 115-0230-085). Route the connectors to the AutoBoom valve (P/N 063-0131-125). Connect the Left Press connector to Port G1 on the AutoBoom valve.

  • Page 51: Install The Center Rack Control

    Connect the coil connector to the installed boom sense adapter cable. Plug the single connectors on the installed boom sense adapter cable to the Center Up harness connectors on the AutoBoom harness cable (P/N 115-0230-045 or 115-0230-085). Locate the center down coil on the machine’s hydraulic valve.

  • Page 52: Connect The Harness To The Sensors

    Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-021). Note: The AutoBoom controller should be mounted in the machine’s cab so that the machine’s operator has easy access to it. Connect the Field Computer (If Applicable) Refer to the Installation &...
  • Page 53 UltraGlide Install the red power lead on the positive battery terminal and reinstall the machine’s battery connector. Install the white power lead on the negative battery terminal and reinstall the machine’s battery connector. Manual No. 016-0230-005...

  • Page 54: Ultraglide Wiring Schematic

    Chapter 4 UltraGlide Wiring Schematic Gen I Cabling Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 55: Gen Ii Cabling

    UltraGlide Gen II Cabling Manual No. 016-0230-005...
  • Page 56 Chapter 4 Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...

  • Page 57: Replacement Parts

    R eplacement Parts CHAPTER C h a p t e r 5 This section contains replacement part diagrams and listings for PowerGlide Plus,and UltraGlide systems. Please refer to these diagrams when calling to request replacement parts. Valve Blocks Valve Block Replacement Parts Manual No.

  • Page 58: Wheels

    Chapter 5 Wheels Sensors Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 59 Hydraulic Fittings 4 Down Hoses Fittings Hydraulic Schematic Left and Right Cylinder Hoses Kit Contents Mount the AutoBoom Valve Pressure and Tank Hoses (Case IH and Patriot PowerGlide Plus 7 1997 & Newer Only) UltraGlide 29 Pressure and Tank Hoses (CaseIH Only)
  • Page 60 Index Case IH 3150/3185, Pre-2002 Tyler Patriot Open Center AutoBoom™ Installation Manual...
  • Page 61 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If your dealer agrees with the warranty claim, the dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.

Table of Contents