Table of Contents
Advertisement
Disposal of Ashes
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a
non-combustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they should be retained in closed container until all cinders
have thoroughly cooled. Other waste should not be placed in this container.
1. Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This
is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is
necessary to burn wet or unseasoned wood, do so only with the air inlet set open enough to maintain a good strong
fire and fairly high chimney temperatures. Do not attempt to burn overnight using green wood or wet wood. Wet
wood can cause up to 25% drop in heater output, as well as contributing significantly to creosote buildup.
WARNING: NEVER USE CHEMICALS OR ANY OTHER VOLATILE LIQUID TO START A FIRE. DO NOT BURN
GARBAGE, OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPTHA, OR ENGINE OIL.
2. Remove ashes frequently. Embers can roll out the door and create a fire hazard. Maintain a 1"(25mm) minimum ash
base.
3. If glass becomes darkened through slow burning or poor wood, it can readily be cleaned with fireplace glass cleaner
when stove is cold. Never scrape with an object that might scratch the glass. The type and amount of deposit on
the glass is a good indication of the flue pipe and chimney buildup. A light brown dusty deposit that is easily wiped
off usually indicates good combustion and dry, well-seasoned wood and therefore relatively clean pipes and chim-
ney. On the other hand, a black greasy deposit that is difficult to remove is a result of wet and green wood and too
slow a burning rate. This heavy deposit is building up at least as quickly in the chimney.
WARNING: ONLY USE MATERIALS AND COMPONENTS SUPPLIED BY MANUFACTURER WHEN DOING
MAINTENANCE OR REPLACEMENTS.
4. DOOR GASKETS - The gasket used on this unit (5/8" medium density fiberglass rope) requires only light pressure
to seal. This will prolong seal life. It is important that the door seal be maintained in good condition. Periodically
inspect seals and replace if necessary. Follow instructions included in the WODC.DG58 kit obtainable from your
nearest Pacific Energy Dealer.
5. DOOR GLASS - Do not slam loading door or otherwise impact glass. When closing door, make sure that no logs
protrude to impact the glass. If the glass gets cracked or broken, it must be replaced before using the stove. Re-
placement glass can be obtained from your dealer. Use 16-1/2"(419mm) x 10-1/2"(267mm) x 5 mm. Ceramic glass
only. Do not substitute with any other type.
To remove broken glass, remove the door gasket and then undo the eight screws securing the gasket guides and
glass retainers. Remove all particles of glass . Be careful as they are very sharp. Install new glass complete with
gasket. Replace glass retainers and gasket guides then install new door gasket as per instructions provided with the
door gasket kit.
CAUTION:
•
Do not overtighten, tighten screws very carefully
•
Do not clean glass when hot
•
Do not use abrasive cleaners on glass
6. The area where boost combustion air enters the firebox must be kept clear of excessive ash buildup which will block
air flow. This area is at the front of the firebox.
7. Do not store wood within heater installation clearances, or within the space required for fuel loading and ash remov-
al. Keep the area around the heater clean and free of loose combustibles, furniture, newspapers, etc.
8. Establish a routine for the fuel, wood burning and firing technique. Check daily for creosote buildup until experience
shows how often you need to clean to be safe.
5055.7298-A
Maintenance
8
210618-28_ALT 1.2
Advertisement
Table of Contents
