Table of Contents
Advertisement
SAFETY NOTICE
If this stove is not properly
installed, a house fire may
result. For your safety, follow
the installation directions.
C o n t a c t l o c a l b u i l d i n g o r
fire officials about restrictions
and installation inspection
requirements in your area.
TESTED and LISTED
to CAN/ULC S627-M93 AND UL 1482-98
Meets the U.S. Environmental Protection
Agency's July 1990 Particulate Emission
STUDY CAREFULLY BEFORE
PROCEEDING
111206-16
Standards
PLEASE SAVE THESE INSTRUCTIONS
VISTA and CLASSIC-C
INSTALLATION
AND OPERATING
INSTRUCTIONS
Models
Pacifi c VISTA
VISTA CLASSIC
SERIES - C
5055.3
Advertisement
Table of Contents
Related Manuals for Pacific energy Paci?c VISTA
Summary of Contents for Pacific energy Paci?c VISTA
- Page 1 SAFETY NOTICE If this stove is not properly installed, a house fire may result. For your safety, follow the installation directions. C o n t a c t l o c a l b u i l d i n g o r fire officials about restrictions and installation inspection requirements in your area.
-
Page 2: Table Of Contents
Contents SAFETY AND MAINTENANCE ....................... 3 ASSEMBLY ............................4 MOBILE HOME INSTALLATION ..................... 6 RESIDENTIAL INSTALLATION ....................... 7 FLOOR PROTECTOR ........................7 COMBUSTION AIR ......................... 8 WOOD SELECTION ........................8 OPERATING ............................ 8 PROPER DRAFT ..........................9 ASH REMOVAL ..........................9 BAFFLE REMOVAL ......................... -
Page 3: Safety And Maintenance
• PLEASE SAVE THESE INSTRUCTIONS • NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to curing of stove paint or fumes caused by accidentally leaving the fi re door open. Do not disconnect the detectors. -
Page 4: Assembly
FIG. #1a Minimum Clearances to Combustibles Single Wall Connector - Residential 10" 15" 20 3/4" 22 5/8" 14" 26" 10" Double Wall Connector - Residential 7" 12 3/4" 16 3/4" 11" 15 5/8" 12" 3" 12" 12" 24" 24" 3" Alcove height - 7' min. - Page 5 FIG. #2 Spark arrestor The chimney may incorpo- rain cap rate an offset. To do this safely, all sections of listed connector, offset elbows and chimney section must be screwed together by Chimney at least three sheet metal screws per joint. The chimney must be suitably supported Storm collar by the chimney manufac-...
-
Page 6: Mobile Home Installation
MOBILE HOME INSTALLATION CHIMNEY AND CHIMNEY CONNECTOR This heater must be installed with double wall connector and Warning: Under no circumstances is this heater to be compatible chimney system listed below. installed in a makeshift or "temporary" manner. It may be NOTE: Longer chimney lengths and different pitch fl... -
Page 7: Residential Installation
RESIDENTIAL INSTALLATION 4. To start installing single wall connector (smoke pipe), slip crimped edge of the pipe inside the stove collar. Use holes provided in collar to secure pipe with two screws. Warning: Under no circumstances is this heater to be 5. -
Page 8: Combustion Air
fi rebox intake. Consult your local building condition. code. Your PACIFIC ENERGY heater is designed for maximum Note: The living space around the heater must be ventilated overall effi ciency at a moderate fi ring rate. Overfi ring is haz- with good air circulation. -
Page 9: Proper Draft
too low a setting. As every home's heating needs vary while pulling ashes into the hole. Avoid large charcoal pieces (i.e.. insulation, windows, climate, etc.) the proper setting as these still contain heat value. Release handle and push in can only be found by trial and error and should be noted to lock. -
Page 10: Optional Blower
OPTIONAL BLOWER Automatic: To operate the blower automatically, set the The optional blower kit (# WODC.BLOW) is equipped with rocker switch on the side of the fan housing to "Auto" and set a three prong power cord and may be installed at any time. the speed control to desired setting. -
Page 11: Creosote Formation And Need For Removal
CREOSOTE FORMATION AND NEED FOR REMOVAL CHIMNEY FIRES hen wood is burned slowly, it produces tar and other or- ganic vapours, which combine with expelled moisture to form The result of excessive creosote buildup is a chimney fi re. creosote. The creosote vapours condense in the relatively Chimney fi... -
Page 12: Replacement Parts - Pacific Vista
REPLACEMENT PARTS - PACIFIC VISTA FIGURE #4a (WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION) ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 ..SIDE SHIELD, LEFT OR RIGHT ..... VIST.2201 .... FIREBRICK, SET ........BRIC.VISTA 2 ..TOP DEFLECTOR ........VIST.2203 12a .. -
Page 13: Replacement Parts - Vista Classic
REPLACEMENT PARTS - VISTA CLASSIC FIGURE #4b (WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION) ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO. 1 ..VISTA CLASSIC SIDE SHIELD, L/R ..VISC.2251_ _ 13 ..RAIL EXTENSIONS (2 pc. required) ....2123 2 .. -
Page 14: Firebrick Installation Instructions
FIREBRICK INSTALLATION INSTRUCTIONS Pacifi c Vista and Vista Classic This package contains 12 full-size fi rebricks, as well as 2 various cut-size bricks. If your heater came with an ash cleanout system, or an optional one is being in- stalled, discard one full-size brick. With the heater in the upright position, install fi... -
Page 15: Safety Label - Pacifi C Vista And Vista Classic
MODEL SS II, METAL FAB MODEL 2100, AMERI-TEC MODEL HS, INDUSTRIAL CHIMNEY MODEL EXCEL 103HT, SIMP- SON DURA-VENT MODEL DURA/PLUS AND DURA TECH. USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. • APPLIANCE MUST BE INSTALLED WITH PEDESTAL OR LEG KIT ATTACHED. - Page 16 PACIFIC ENERGY FIREPLACE PRODUCTS LTD. 2975 Allenby Rd., Duncan, BC V9L 6V8 Phone: 888-715-2398 Web site: www.pacifi cenergy.net Printed in Canada VISTA and CLASSIC-C 111206-16...