IBM 3745 Service Functions page 87

Display/Alter Scanner
Display/Alter Scanner Control Storage
1. You must be in the TSS function (see 4-4).
2. The scanner must be selected (details in
"Select Scanner" on page 4-5).
3. Select function 4 (details page 4-4).
4. In
D, fJ
and
IJ
type the values according
to the instructions on the screen.
5. Press SEND.
6. Screen
m
is displayed.
Default values: 32 halfwords, I (immediate).
Note: Option D delays the execution for an
address compare (details page 4-16).
aaaa Storage address
xxxx Storage data
Alter the Scanner Control Storage
- - Possib!s Disii.iption
I
Any ALTER may be disruptive.
Press F4. Screen
m
is displayed.
1. Move the cursor to the data you wish to
modify.
2. Modify the data.
3. When you have altered all desired data, type
D or I in
0
and press SEND.
All displayed data, altered or not, is transmitted to
the scanner.
To cancel the alter, press F6 at any time before
SEND. The modifications you have already
entered on the screen are ignored.
4-10
3745 Service Functions
D
1 SELECT/RELEASE I - ENTER HALFWORD STORAGE ADDRESS
0
2 DU~lP/lML I ROS: ees TO FFF - RAM: lese TO FfFF
3 MODE CONTROL I - ENTER
NU~lBER
OF HALFIIORDS TO DISPLAY (UP TO 32) ==>
D
DPLY/ALT STORE I
DPLY/ALT BLOCKSI
6 DPLY/ALT LSR I - ENTER I FOR IMMEDIATE EXECUTION. 0 FOR DELAYED ==>
II
DPL Y /AL T XREG I
AOORESS COMPARE I
9 CHK-PDINT TRACE I
IS DPLY/ALT HPTSS I
===> TO ALTER DATA. SPECIFY AN IMMEDIATE DISPLAY
F1 :END F2:MENU1 f3:ALARM
Figure 4-12. Display/Alter Scanner Storage Selection
Screen
m
SELECT/RELEASE I - ENTER HALFWORD STORAGE ADDRESS
DUMP/lML I ROS: 909 TO FFF - RAM: lees TO FFFF
3 MODE CONTROL I - ENTER NUMBER OF HALFIIORDS TO DISPLAY (Up TO 32)==>
DPLY /AL T STORE I
DPLY/ALT BLOCKSI
DPLv/4lT lSI!
f -
ENTER! FOR !~EO!ATE ElCErUT!ON, 0 FOR OElAYED ==>
7 DPLY/ALT XREG I
ADDRESS COMPARE I
aaaa xxxx xxxx xxxx
XXX)(
CHK- POI NT TRACE
I aaaa xxxx xxxx xxxx xxxx xxxx xxxx xxxx
19 DPLY/ALT HP"TSS I
aaaa ,<xxx xxxx xxxx xxxx xxxx xxxx xxxx
mm
I!IZI!I
xxxx xxxx xxxx xxxx xxxx xxxx
Fl:END F2:MENU2 F3:ALARM
'$'·"U;I
F5:REFRESH F7:BACKIIARD F8:FORWARD
Figure 4-13. Scanner Storage Display Screen
m
1 SE LECT /RELEASE I - ENTER HALFWORD STORAGE ADDRESS
DUMP/IML I ROS: e99 TO FfF - RAM: 1999 TO FFFF
MODE CONTROL I - ENTER NUMBER OF HALFWORDS TO DISPLAY (UP TO 32) ==>
DPLY/ALT STORE I
OPLY/AlT BLOCKSI
6 DPLY /ALT LSR I - ENTER I fOR IMMEDIATE EXECUTION. 0 FOR DELAYED ==>
D
DPLY /AL T XREG
I
ADDRESS COMPARE I aaaa
XXXl(
xxxx
XXXX
xxxx xxxx xxxx
CHK-POINT TRACE I
aaaa xxxx xxxx xxxx xxxx xxxx
1 e DP L Y / AL T HPT SS I
aaaa xxxx xxxx xxxx xxxx xxxx xxxx
aaaa xxxx xxxx xxxx
===> TO DELAY ALTER. ENTER NEW DATA; CHANGE I TO D. PRESS SEND
Fl :END f2:MENU2 f3:ALARM F6:IGNORE ALTER
Figure 4-14. Scanner Storage Alter Screen
\,,-
(