Lan Settings - jablotron JA-101K Manual

the limiter of alarm SMSes is set to 20. The system behaviour will be like the following: When during one day
any type of 30 SMSes are sent (alarm and non-alarm), the system won´t send any non-alarm SMSes that day.
But it can still send alarm SMSes (but 20 is the maximum). This ensures that the system always has some
reserve for the case of an alarm to be able to inform the user by SMS.
Allow diacritic – if international character accents (ICC) are allowed, reports can be sent from the system
via more than one SMS text message. ICC must be enabled if you use e.g. Russian alphabet in your texts etc.
Remote control via telephone – setting the possibility to control the system remotely using the voice menu.
If Users are selected, the menu can only be accessed from the phones of defined users (in the Communication
tab you can even allow users to enter the voice menu without entering their user code – the Voice menu without
code option). If "Anybody" is selected, the voice menu can be accessed from any phone. However,
on accessing the menu the user is always requested to enter the user's code.
Remote control by sending SMS – setting the possibility to control the system remotely with the use of SMS
commands. If Users are selected, the system only accepts SMS commands from the phones of defined users
(in the Communication tab you can even allow users to use SMS commands without entering their user code –
the Voice menu without code option). If "Anybody" is set, an SMS command can be set from any phone;
however, it is conditional on entering the access code.
Credit enquiry – by pressing this button you can immediately get information about the credit balance from
the operator's answer (it this function is support)
Credit - limit – possibility to set the lower limit for automatic checking of the limit of a pre-paid SIM card.
If the established credit is below this limit, the system will send and information SMS to the person whom
the reports SMS Errors and Service are assigned to. Caution: you are not recommended to use a pre-paid
card in the system – they increase the risk of a communication failure.
SIM credit sequence – command for automatic checking of the credit balance of a pre-paid SIM card
(if supported by the operator). You can obtain the command from your operator.
Credit - position in text – position (sequential number of the character) in the operator's credit balance report
at which the numerical information about the credit balance starts (the communicator only looks for numerals
in the report and ignores the other characters)
Credit - checking period – setting how often the system will check the credit balance (you can set 0 to 99
days where 0 is off).
Tel.no. to maintain SIM card validity – if the pre-paid SIM card requires maintaining calls, you can set
a phone number which the system will dial automatically (e.g. the exact time service) if there has not been any
outgoing call from the system for a period longer than 90 days (10 s after answering of the call by the called
party the system will hang up).
SIMLock – function that links the phone number of the SIM card to the ARC settings. It means that if you
replace the SIM card with another one and the SIM will be logged in to the GSM network, all the settings
of the ARC tab will be deleted. The deletion is irreversible and other settings (registration
to the MyJABLOTRON web service) must be performed by the ARC technician once again.
Sensitivity of DTMF detection from ARC – setting the sensitivity of reception of the signal generated
by the ARC. The sensitivity is adjustable in 10 steps; the optimum default value is 4.
Level of generated DTMF to the ARC – setting the intensity of the transmitted tone dialling signal in DTMF
generated by the control panel. The intensity is adjustable in 10 steps; the optimum default value is 4.
Number of incoming
by the communicator. You can set answering after 1 to 10 ringing impulses (corresponding to 5 to 50 seconds).
The default value is 3 (15 seconds).
Network mode – a parameter meant for the automatic selection between 3G and 2G networks or the option
for a 2G network only (no automatic switching). Select 2G mode only if the 3G connection is not stabile or too
weak for reliable connection. See F-Link SW to get more detailed information about current GSM signal quality.
10.11.2

LAN Settings

It is used to set the LAN communicator (if the control panel contains one).
LAN communicator – possibility to enable or disable LAN communication.
Get IP address from the DHCP server - automatic setting of network parameters. If this function
is not supported by the network, the respective parameters must be entered manually. Manual entry is only
possible if this option is deselected.
JA-101K(-LAN)(-LAN3G) and JA-106K(-3G)
Security System Control Panels
call rings – number of ringing impulses
85 / 110
until automatic answering
MLJ51410