Beretta EXCLUSIVE C Installer And User Manual page 38

EXCLUSIVE
11 INFO
The INFO function can be used to display a series of data regarding the
system.
ATTENTION - The displayed data cannot be modified.
Press the "up" and "down" keys to go through the list of information
available, in this order:
- SCREED HEATER OPERATING HOURS
- FLOW PROBE
- RETURN PROBE
- DOMESTIC HOT WATER PROBE
- FLUE GAS PROBE
- OUTDOOR TEMPERATURE SENSOR
- EXT T FOR THERMOREG
- FAN
- ZONE 1 DELIVERY
- ZONE 2 DELIVERY
- FLUE GAS PROBE OP. HOURS
- MAIN ZONE SET-POINT
- ZONE 1 SET-POINT
- ZONE 2 SET-POINT
- SYSTEM PRESSURE.
The "ok" key is inactive.
The "back" key allows you to return to the initial screen.
In the absence of additional zones or if the screed heater function is not
operating, the relative information will not be displayed.
12 MENU
Using the MENU it is possible to access the configuration of the SETTINGS
and the TOME SCHEDULE (available only if the timer is enabled (POR=1).
To do this, it is necessary to highlight the desired entry using the "up" and
"down" keys and then pressing "ok" to confirm the selection.
Pressing "back" takes you back to the initial screen without making any
selection.
TIME SCHEDULE TIME SCHEDULE
SELECT OPTION SELECT OPTION
12.1 Settings
Select this function to modify the following settings:
- TIME AND DATE
- LANGUAGE
- BACKLIGHT.
To access the desired setting, it is necessary to highlight it using the "up"
and "down" keys and then pressing "ok" to confirm the selection.
Press "back" to return to the start screen without making any selection.
SELECT OPTION SELECT OPTION
12.1.1 Time and date
Press "ok" to highlight in sequence HOURS, MINUTES, DAY, MONTH,
YEAR and press the "up" and "down" keys to change the desired values.
Once the sequence has finished by pressing "ok", the settings will be
saved and the display will return to the initial screen.
By pressing "back" at any time the system will return to the
cancelling the changes that were made.
38
MENU MENU
SETTINGS
SETTINGS
SETTINGS
SETTINGS
TIME & DATE
TIME & DATE
LANGUAGE
LANGUAGE
BACKLIGHT BACKLIGHT
12.1.2 Language
Press the "up" and "down" keys to select the desired language.
Pressing "ok" the language selection is confirmed and the display returns
to the initial screen.
Pressing "back" the system returns to the
changing the system's language.
12.1.3 Backlight
The screen saver display (backlight off) is automatically activated when
the time, that has been set in parameter \ MENU \ SETUP \ BACKLIGHT,
elapsed without having pressed any buttons.
In the screen saver the current time is normally displayed.
When there is a heat request, the current time is replaced with the boiler
flow temperature and turns on the icon concerning the type of request in
progress.
A message for the system efficiency level can be displayed in the top of
the screen:
- HIGH EFFICIENCY (if the average value of the return probe > 55°C)
- OPTIMUM EFFICIENCY (if 25°C < average value of the return probe <
.
55°C)
12.1.4 Time schedule
Selecting this function, only if the time schedule is enabled (POR=1), it is
possible to change the following:
- MAIN
- ZONE 1
- ZONE 2.
SETTINGS
To access the desired timer programme , it is necessary to highlight it using
the "up" and "down" keys and then pressing "ok" to confirm the selection.
Press "back" to return to the start screen without making any selection.
For a detailed description of the scheduled programming timer, please refer
to the section "13 PROGRAMMING TIMING" .
TIME & DATE
TIME & DATE
ENTER TIME AND DATE
ENTER TIME AND DATE
12 : 17
18 / 11 / 2013
USE THE ARROWS TO MODIFY USE THE ARROWS TO MODIFY
SETTINGS
LANGUAGE
LANGUAGE
ENGLISH ENGLISH
ITALIANO
ITALIANO
SELECT LANGUAGE SELECT LANGUAGE
: 30 days DAYS
05:11
OPTIMAL EFFICIENCY
OPTIMUM EFFICIENCY
: 30 days DAYS
42
°C
screen without
P