Table of Contents
Advertisement
Available languages
Available languages
EXCLUSIVE
- Adjust the room thermostat to the desired temperature (~20°C) or, if the
system is equipped with a chronothermostat or programmable timer or
REC10 set as an ambient regulator, ensure that the thermostat or timer
is "active" and set correctly (~20°C)
- Then set the boiler for WINTER selecting the STATE menu on the
REC10 and then BOILER, based on the season and the type of operation
selected.
FRI
FRI
18/05/2013
MENU
MENU
HOT WATER TEMPERATURE
HOT WATER TEMPERATURE
P
HEATING AND HOT WATER
230 V
N L
F= 3.15A F
230 V
ausiliario
- When there is a heat request and the boiler is igniting, the icon
M3
"
" appears on the display. The boiler will start up and continue working
F
until the set temperatures are reached, after which it will then go back
to standby.
blu
blu
marrone
marrone
VENT CYCLE FUNCTION
b
Each time the boiler is started up an automatic venting cycle is
carried out lasting 2 min. When the vent cycle is in progress, all heat
requests are inhibited and a sliding message at the foot of the page
appears on the main page of the REC10.
1
In this condition the green and red LEDs light up alternately for 0.1
sec with a pause of 0.5 sec and 1 sec between one ignition and
another.
X15
X4
X6
X3
1
5
1
3
1
24
AKM0x
PLANT
PLANT
12:17
1.3 bar
STATE
STATE
42
°C
INFO
INFO
SET
SET
STATE
STATE
BOILER
BOILER
MAIN ZONE
MAIN ZONE
BOILER
BOILER
OFF
OFF
HOT WATER ONLY
SUMMER
WINTER
V Hv
2
1
X15
arancione
combustion analysis button SW1
E.R.
X7
SW1
6
1
5
1
b
The vent cycle can be interrupted beforehand by removing the cap
from the instrument panel and pressing the combustion analysis
button SW1 or else from the TECHNICAL menu of the REC10 in the
following way:
- access the technical parameters as explained in the section "4.1 Access
to the technical parameters"
- select VENT CYCLE with the "up" and "down" keys, confirming the
selection
INSTALLER
- select STOP FUNCTION with the "up" and "down" keys, confirming
the selection.
INSTALLER
The REC10 will briefly display a wait message after which you will
automatically be taken to the main screen.
FRI
FRI
18/05/2013
C.S.A.
SUMMER
: selecting SUMMER operating mode in the STATE menu
5
4
3
2
1
and then BOILER, the traditional function of just domestic hot water will be
activated. The REC10 normally displays the temperature of the domestic
hot water supplied by the boiler.
X4
WINTER
/
BOILER, the heating and domestic hot water functions are activated.
REC10 normally displays the domestic hot water temperature unless
there is a heating request in progress, in which case the boiler's outlet
temperature is displayed.
TECHNICAL
TECHNICAL
WEATHER COMPENSATION
THERMOREGULATION
RANGE RATED
RANGE RATED
CALIBRATION
CALIBRATION
COMBUSTION ANALYSIS
SWEEPER
AIR PURGING CYCLE
VENT CYCLE
INSTALLER
AIR PURGING CYCLE
VENT CYCLE
DISABLE FUNCTION
DISABLE FUNCTION
ENABLE FUNCTION
ENABLE FUNCTION
STOP FUNCTION
STOP FUNCTION
INSTALLER
PLANT
PLANT
1.3 bar
MENU
MENU
TSC2
N
30
F
°C
.3
INFO
INFO
SET
SET
HOT WATER TEMPERATURE
HOT WATER TEMPERATURE
3
2
1
X6
BOILER
BOILER
OFF
OFF
HOT WATER ONLY
SUMMER
BE20
HEATING AND HOT WATER
WINTER
1
2 3
4
J1
: selecting WINTER in the STATE menu and then
12:17
STATE
STATE
EA
1415 16
+
B
A
Advertisement
Table of Contents
