Table of Contents
Advertisement
Available languages
Available languages
EXCLUSIVE
7
START SCREEN
Upon ignition, the REC10 might:
- request the setting of the time and date (see paragraph "12.1.1 Time
and date" ).
- display the firmware version and require a button to be pressed in order
to continue.
By pressing the "up" and "down" keys it is possible to move the selection
of the functions in this order:
- PLANT
- STATE
- SET
- INFO
- MENU.
By pressing the "ok" key you access the settings of the selected function
(except for
PLANT
).
The "back" key is inactive (except for
FRI
FRI
18/05/2013
MENU
MENU
INFO
INFO
HOT WATER TEMPERATURE
HOT WATER TEMPERATURE
8
PLANT
This item does not represent any specific function.
Instead, it indicates the zone to which the data shown on the start screen
refer, and the zone to which the settings accessible via the other functions
refer.
The presence of one or more zones in addition to PLANT depends
upon the installation's configuration. For this reason, one or more of
the zones cited below may not be present in your configuration, or may
be identified with a different name.
In order to change zones, highlight PLANT if necessary pressing the "up"
and "down" keys.
Then, pressing the "ok" and "back" keys, it will be possible to select the
other zones in this sequence:
- PLANT
- MAIN ZONE
- ZONE 1
- ZONE 2.
The TIME AND DATE, LANGUAGE and BACKLIGHT settings are
independent of the selected zone.
The information contained in the INFO menu is independent of the selected
zone.
No domestic hot water parameters can be set if MAIN, ZONE 1 or ZONE
2 is selected.
9
STATE
The
STATE
function can be used to set the
operating modes.
To do this, it is necessary to highlight the desired entry using the "up" and
"down" keys and then pressing "ok" to confirm the selection.
Pressing "back" takes you back to the initial screen without making any
selection.
36
).
PLANT
PLANT
PLANT
12:17
1.3 bar
STATE
STATE
42
°C
SET
SET
BOILER
and
STATE
STATE
BOILER
BOILER
MAIN ZONE
MAIN ZONE
9.1
Boiler
This function can be selected in order to set the boiler's status, by choosing
one of the following options:
- OFF
- SUMMER
- WINTER.
The highlighted status is that which is currently selected. In order to select a
different status highlight it using the "up" and "down" keys and then press
"ok" to confirm the selection.
Once the selection has been validated, the display returns to the
screen.
Press "back" to return to the start screen without making any selection.
9.1.1
OFF
If OFF is selected, the system shuts off.
The electrical supply and the fuel supply remain active.
9.1.2
Summer
If SUMMER is selected, the system produces domestic hot water.
Heating is not enabled.
9.1.3
Winter
If WINTER is selected, the system produces domestic hot water and
activates the heating function.
9.2
Main zone
Selecting this function allows you to set the main zone's status, by choosing
one of the following options:
- if the heating programming timing is not enabled:
- ZONE ON
- ZONE OFF
- if the heating programming timing is enabled:
- AUTO
- MANUAL
- HEAT OFF.
MAIN ZONE
In order to select a different status highlight it using the "up" and
"down"keys and confirm the selection by pressing "ok".
Once the selection has been validated, the display returns to the STATE
screen.
Press "back" to return to the STATE screen without making any selection.
BOILER
BOILER
OFF
OFF
HOT WATER ONLY
SUMMER
HEATING AND HOT WATER
WINTER
MAIN
MAIN
ZONE ON
ZONE ON
ZONE OFF
ZONE OFF
MAIN
MAIN
AUTO
AUTO
MANUAL
MANUAL
HEAT OFF
HEAT OFF
STATE
Advertisement
Table of Contents
