Eaton PowerXL DC1 Manual page 47

1)
P-15 DI1
0, 1, 5, 0 = Locked
8 - 12 1 = Start-Enable
2 0 = Locked
1 = Start enable FWD
3 0 = Locked
1 = Start enable FWD
4 0 = Locked
1 = Start enable FWD
6 0 = Locked
1 = Start-Enable
7 0 = Locked
1 = Start enable FWD
1)
P-15 DI1
0, 1, 2, 0 = Locked
4, 5, 1 = Start enable FWD
8 - 12
3 0 = Locked
1 = Start enable FWD
6 0 = Locked
1 = Start enable FWD
7 0 = Locked
1 = Start enable FWD
1)
P-15 DI1
0, 2, 4, 0 = Locked
5, 1 = Start enable FWD
8 - 12
1 0 = Locked
1 = Start enable FWD
3, 6, 7 0 = Locked
1 = Start enable FWD
1) FWD switch position only for IP66 degree of protection with local controls
2) REV switch position only for IP66 degree of protection with local controls
3) Button command
Keypad Mode (P-12 = 1, 2)
2)
DI2 DI3/AI2
1 = Increase 1 = Reduce frequency
3)
frequency
1 = Increase 1 = Reduce frequency
3)
frequency
1 = Increase External fault
3)
frequency 0 = Fault
1 = Enable
1 = Increase 0 = Source of setpoint: keypad,
3)
frequency DI2
1 = Frequency via AI1
0 = FWD External fault
1 = REV 0 = Fault
1 = Enable
0 = Locked External fault
1 = Start enable REV 0 = Fault
1 = Enable
CANopen / Modbus control mode (P-12 = 3, 4, 7, 8)
2)
DI2
Not assigned
0 = Source of setpoint:
Modbus
1 = FF1 (P-20)
0 = Source of setpoint:
Modbus
1 = Source of setpoint: AI1
0 = Source of setpoint:
Modbus
1 = Source of setpoint:
keypad
User PI control mode (P-12 = 5, 6)
2)
DI2 DI3/AI2
0 = PI Regulation PI feedback
1 = FF1 (P-20) Analog input
0 = PI Regulation PI feedback
1 = Source of setpoint: Analog input
AI1
0 = PI Regulation External fault
1 = FF1 (P-20) 0 = Fault
1 = Enable
DC1 variable frequency drive 12/13 MN04020003Z-EN www.eaton.com
AI1/DI4
3)
0 = FWD
1 = REV
3)
0 = Source of
setpoint: keypad,
DI2/DI3
1 = FF1 (P-20)
1 = Reduce
frequency
Setpoint value AI1
0 = Source of
setpoint: keypad
1 = FF1 (P-20)
0 = Source of
setpoint: keypad
1 = FF1 (P-20)
DI3/AI2 AI1/DI4
Not assigned Not assigned
External fault Not assigned
0 = Fault
1 = Enable
External fault Setpoint value AI1
0 = Fault
1 = Enable
External fault Not assigned
0 = Fault
1 = Enable
AI1/DI4
Not assigned
Setpoint value AI1
PI feedback
Analog input
5 Parameters
5.5 Digital and analog inputs
Notes
Press the Start button or
P-31 = 2 or 3
Press the Start button or
P-31 = 2 or 3
Press the Start button or
P-31 = 2 or 3. Used to connect an
external thermistor to DI3.
Press the Start button or
P-31 = 2 or 3
Press the Start button or
P-31 = 2 or 3. Used to connect an
external thermistor to DI3.
Press the Start button or P-31 = 2
or 3. Connecting DI1 and DI2 will
trigger a quick stop (P-24). Used
to connect an external thermistor
to DI3.
Notes
Run and stop commands will be trans-
mitted via the RS-485 connection; in
order for the variable frequency drive
to run, DI1 must be switched.
Used to connect an external therm-
istor to DI3.
Master speed reference value: Start
and stop controlled via RS-485.
Keypad speed reference value:
The variable frequency drive will run
automatically: if DI1 is closed –
depending on P-31. Used to connect
an external thermistor to DI3.
Notes
Used to connect an external
thermistor to DI3.
101