Eaton PowerXL DC1 Manual page 46

5 Parameters
5.5 Digital and analog inputs
1)
P-15 DI1
0 0 = Locked
1 = Start-Enable
1 0 = Locked
1 = Start enable FWD
2 0 = Locked
1 = Start enable FWD
3 0 = Locked
1 = Start enable FWD
4 0 = Locked
1 = Start enable FWD
5 0 = Locked
1 = Start enable FWD
6 0 = Locked
1 = Start-Enable
7 0 = Locked
1 = Start enable FWD
8 0 = Locked
1 = Start-Enable
9 0 = Locked
1 = Start enable FWD
3)
10 1 = Run FWD
3)
11 1 = Run FWD
12 0 = Locked
1 = Start enable FWD
Note:
Negative fixed frequencies are inverted it Run REV is selected.
1) FWD switch position only for IP66 degree of protection with local controls
2) REV switch position only for IP66 degree of protection with local controls
3) Button command
100
Terminal Mode (P-12 = 0)
2)
DI2 DI3/AI2
0 = FWD 0 = Selected setpoint source
1 = REV 1 = Fixed frequency 1 (P-20)
0 = Selected setpoint 0 = Fixed frequency 1 (P-20)
source 1 = Fixed frequency 2 (P-21)
1 = fixed frequency 1/2
DI2 DI3/AI2 DI3/AI2
0 0 0
1 0 0
0 1 1
1 1 1
0 = Selected setpoint External fault
source 0 = Fault
1 = fixed frequency 1 1 = Enable
(P-20)
0 = Analog input 1 Setpoint value AI2
1 = Analog input 2
0 = Locked 0 = Selected setpoint source
1 = Start enable REV 1 = Fixed frequency 1 (P-20)
0 = FWD External fault
1 = REV 0 = Fault
1 = Enable
0 = Locked External fault
1 = Start enable REV 0 = Fault
1 = Enable
0 = FWD DI3/AI2
1 = REV
0
1
0
1
0 = Locked DI3/AI2
1 = Start enable REV
0
1
0
1
3)
0 = Stop 0 = Selected setpoint source
1 = Fixed frequency 1 (P-20)
3)
0 = Stop 1 = Run REV
0 = Quick stop (P-24) 0 = Selected setpoint source
1 = Run FWD 1 = Fixed frequency 1 (P-20)
DC1 variable frequency drive 12/13 MN04020003Z-EN www.eaton.com
AI1/DI4
Setpoint value AI1
Setpoint value AI1
Fixed
frequency
FF1 (P-20) 0 = Fixed
frequency 1 - 4 (P-
FF2 (P-21)
20 - P-23)
FF3 (P-22)
1 = maximum
frequency (P-01)
FF4 (P-23)
Setpoint value AI1
Setpoint value AI1
Setpoint value AI1
Setpoint value AI1
Setpoint value AI1
AI1/DI4 Fixed frequency
0 FF1 (P-20)
0 FF2 (P-21)
1 FF3 (P-22)
1 FF4 (P-23)
AI1/DI4 Fixed frequency
0 FF1 (P-20)
0 FF2 (P-21)
1 FF3 (P-22)
1 FF4 (P-23)
Setpoint value AI1
3)
Setpoint value AI1
Setpoint value AI1
Notes
4 selectable fixed frequen-
cies:
The analog input is used as
digital input.
Switched at:
8 V < V < 30 V
input
Used to connect an external
thermistor to DI3
Changing between analog
input: 1 and 2
Connection of DI1 and DI2
leads to a quick stop (P-24).
Used to connect an external
thermistor to DI3
Connection of DI1 and DI2
leads to a quick stop (P-24).
Connection of an external
thermistor to DI3.
Connection of DI1 and DI2
leads to a quick stop (P-24).
Connection of DI1 and DI2
leads to a quick stop (P-24).