Craftex CX Series Manual
8" slow speed grinder
Hide thumbs
Also See for CX Series:
- User manual (48 pages) ,
- Manual (42 pages) ,
- Owner's manual (35 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Craftex CX Series
Summary of Contents for Craftex CX Series
- Page 1 MODEL CX911 8" SLOW SPEED GRINDER Version 1.0...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Safety Instructions ................. 3 Specific Safety Instructions................5 Power Supply ....................6 Machine Specifications ................7 Unpacking....................8 Inventory...................... 9 Overview...................... 10 Assembly ..................... 11 Operating ....................13 Changing the Grinding Wheels..............16 Parts Diagram....................18 Parts List...................... -
Page 3: General Safety Instructions
CX911 SLOW SPEED GRINDER CRAFTEX CX SERIES General Safety Instructions: 2.) Read through owner’s manual thoroughly and understand how to use this Operating a bench top grinder can be machine for its intended applications. dangerous if safety precautions and common sense are not followed. - Page 4 10.) Childproof workshop area 20.) Maintain your machine. Always keep removing all switch keys from machinery, machine clean and in proper working order. unplugging all equipment, or by use of Dress the grinding wheels and replace other padlocks. abrasive accessories when worn out. 11.) Always remove or unplug machine from 21.) Before machine operation check for any power...
-
Page 5: Specific Safety Instructions
Specific Safety Instructions For Bench Top Grinders 1.) Read the instructions thoroughly and 7.) The Grinding wheel should be dressed understand before operation often to keep the wheel surface flat and free of machine. contaminates like residue or glaze. 2.) Use shields wheel guards... -
Page 6: Power Supply
POWER SUPPLY AVAILABILITY OF POWER CIRCUIT REQUIREMENTS FOR Before Installation of this machine you will need CX911 SLOW SPEED GRINDER to consider the proximity of your power supply The CX911 has been prewired at the circuit. If available circuits do not meet the factory for operation on an electrical circuit requirements for this machine you will have to that has a verified ground and meets the... -
Page 7: Machine Specifications
NOTE NOTE The three prong plug is only to be plugged 1. We recommend that you do not use an in to the matching receptacle that is extension cord with this machine. Also the properly installed according to the local longer the extension cord the greater the electrical codes and standards. -
Page 8: Unpacking
UNPACKING The CX911 will require minimal assembly. 3.) Compare all the items from the carton with 1.) Remove the contents form the carton and Figure A. Make sure all items in the place all items on a clean clutter free work inventory accounted before... -
Page 9: Inventory
INVENTORY Small Parts and Safety Guards The following are items are provided in the shipping carton for CX911 Slow Speed Grinder. A. Eye Shield Assembly Regular(2) K. Flat Washers D6 (4) and 2.5 x magnification (2) L. Lock Washers D6 (2) B. -
Page 10: Overview
CX911 SLOW SPEED GRINDER OVERVIEW CX911 Slow Speed Grinder CX911 OVERVIEW: ( May look different than actual ) A. Work Light H. On/Off Switch With Removeable Safety B. Eye Shield Adjustment Knobs (4) C. Eye Shield Magnifier Assembly Right (2) I. -
Page 11: Assembly
ASSEMBLY INSTRUCTIONS FOR CX911 The CX911 Slow Speed Grinder is equipped rest adjustment knobs M-15 (H) as shown in with left and right tool positioned tool rests to Fig. D below. lay your work piece on. 3.) Adjust both of the tool rests until the inside 1.) Make sure that the CX911 on/off switch is in edge facing the grinding wheels (I) is 1/16”... - Page 12 Eye Shields 1.) Secure fasten safety shield assemblies to the safety shield brackets using the supplied fastening knobs M5-15 in Fig. F Permanent Mounting Instructions below. Use the pre drilled mounting holes located 2.) Join the safety shield assembly and bracket to in the base of the CX911.
-
Page 13: Operating
CAUTION!!! WARNING!!! Always wear approved eye protection as this To help reduce and avoid the risk of injury machine generates flying debris and sparks secure the CX911 Slow Speed Grinder to a during operation. solid stable work surface. If not mounted to a solid work surface permanently and remaining portable always secure with Stand at the side of the grinder and plug the... - Page 14 and grind slowly as this will allow for the CAUTION!!! grinding wheel to warm up and prevent Always wear approved eye protection when or minimize the chances of wheel performing operations on your CX911 slow breakage. Never grind anything with the speed grinder.
- Page 15 OPERATING YOUR CX911 SLOW SPEED GRINDER How To Use The Wheel Dresser 4.) Slowly bring the head of the wheel A wheel dresser should be used to help dresser until it lightly makes contact with eliminate any forward wobble of the the grinding wheel (C).
-
Page 16: Changing The Grinding Wheels
Changing The Grinding Wheels 6.) Take off the outer wheel flange (H) and then remove the grinding wheel (I) from the arbor shaft (G). CAUTION!!! The replacement grinding wheel should have a rating for a higher RPM then the grinders motor. - Page 17 Wire Wheels And Buffing Wheels Lubrication: (Not included) The CX911 is equipped with sealed bearings that are located in the motor housing and are pre lubricated. They will not require any additional lubrication. Cleaning: While the machine is turned off and removed from its power source slowly turn the grinding wheels by hand inspecting them...
-
Page 19: Parts List
PART LIST CX911 ITEM DESCRIPTION QTY. ITEM DESCRIPTION Locking knob Bearing Left wheel guard cover Rotor I type hex nut Power cord Flange Cord clip Grinding wheel 60# Screw M5X8 Screw M6X18 Cord plate Spark deflector Base Screw M5X10 Lamp Left wheel guard Led light Left movable tool rest... -
Page 20: Warranty
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels, punches etceteras. Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to property or for incidental contingent, special or consequential damages arising from the use of our products.