Technical Specifications Of The Product - Nice ALTO Instructions And Warnings For Installation And Use

Table of Contents

Available languages

ALTO100C gearmotor, for swing gates

• Product type: electromechanical gearmotor for the automation of automatic gates and doors with built-in control unit complete with radio recei-

ver for "ECCO5..." transmitters

• Adopted technology: DC motor; epicyclical gear reducer; manual motor release. An internal power supply unit housed inside the motor but

separated from the control unit, reduces the mains voltage to the nominal 24V

• Maximum torque: 100 Nm

• Nominal torque: 50 Nm

• No-load speed: 0,20 rad/s ÷ 0,30 rad/s

• Speed at nominal torque: 0,16 rad/s ÷ 0,24 rad/s

• Maximum frequency of operating cycles: 50 cycles per hour (maximum 100 cycles per day)

• Maximum time for continuous operating: about 10 minutes

• Application limits: the product can be used with gates with weights up to 180 kg (leaf of 0.8 m) or with leaf lengths of up to 1.6 m and opening

angle up to 110°

• Mains power-supply: 230 V

• Absorbed power: 120 W

• Backup power supply: for "PR200" buffer batteries

• Flashing light output: for flashing Led lights (mod. FL200)

• "BUS" output: 1 output with maximum load of 7 ECSBus units

• "SbS" input: For normally open contacts (closure of the contact prompts the "Step-by-Step" command)

• "STOP" input: for normally open and/or 8.2kohm constant resistance type contacts, or normally closed contacts with self-learning of the "nor-

mal" status (a variation with respect to the memorised status generates a "STOP" command

• Radio Aerial input: 50 ohm for RG58 or similar type cable

• Max. cable length: mains power-supply: 30 m; motor outputs: 10 m; other inputs/outputs: 20 m with aerial cable preferably less than 5 m

(observe warnings regarding the minimum section and type of cables)

• Ambient operating temperature: -20°C...+50°C (gearmotor efficiency is reduced at lower temperatures)

• Assembly: vertical, with dedicated fixing plate

• Protection rating: IP 44

• Dimension /

eight: 385 x 90 x 123 mm / 4,8 kg

• Possibility of radio control: with "ECCO5..." transmitters, the control unit is set to receive one or more of the following commands: "Step-by-

Step", "Partial Open", "Only Open" and "Only Close"

• Compatible ECCO5... transmitters: up to 256 if memorised in "Mode I"

• ECCO5... transmitter range: from 50 to 100 m. This distance may vary in the presence of obstacles and/or electromagnetic disturbance pre-

sent, and is influenced by the position of the receiving antenna built into the FL200 flashing light

• Programmable functions: "semi-automatic" function (after opening the control unit does not re-close the gate automatically) or "automatic"

function (after opening the control unit re-closes the gate automatically); motor speed "low" or "high"; in the case of "automatic" mode the pause

time can be selected from 10, 20, 40, and 80 seconds; "pedestrian" opening can be selected in 4 different modes; system obstacle detection

sensitivity can be selected from 4 levels; "Step-by-Step" command operation can be selected from 4 modes

• Self-programmed functions: self-detection of devices connected to output "BUS"; self-detection of type of "STOP" device (contact type NO,

NC or 8.2 kohm constant resistance); self-detection of the opening angle for each motor; self-detection of number of gearmotors present in auto-

mation (1 or 2)

ALTO100M gearmotor, for swing gates

• Tipologia: electromechanical gearmotor for automations of automatic gates and doors

• Product type: DC motor; epicyclical gear reducer; manual motor release

• Maximum torque: 100 Nm

• Nominal torque: 50 Nm

• No-load speed: 0,20 rad/s ÷ 0,30 rad/s

• Speed at nominal torque: 0,16 rad/s ÷ 0,24 rad/s

• Maximum frequency of operating cycles: 50 cycles per hour (maximum 100 cycles per day)

• Maximum time for continuous operating: about 10 minutes

• Application limits: the product can be used with gates with weights up to 180 kg (leaf of 0.8 m) or with leaf lengths of up to 1.6 m and opening

angle up to 110°

• Power supply: 24 V

(50%)

• Rated current absorption: 2A; on start-up the maximum absorbed current is 3A for a maximum time interval of 2 s

• Ambient operating temperature: -20°C...+50°C (gearmotor efficiency is reduced at lower temperatures)

• Assembly: vertical, with dedicated fixing plate

• Protection rating: IP 44

• Dimensions /

eight: 385 x 90 x 123 mm / 4,3 kg

––––––––––––

NOTES: • The kit ALTO101START and ALTO100 is produced by Nice S.p.a. (TV) I • In order to improve its products, Nice S.p.a. reserves the right

to modify the technical characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the

intended purposes. • All technical specifications refer to a temperature of 20°C.