Ford COUGAR 1968 Shop Manual page 857

PART 18-1
-
Interior Trim And Roof Outside Cover 18-1 3
VlEW A
FIGURE 3
--.. --..
VlEW B
VIEW
C
VIEW D VlEW
E
I
-
INS'T. PANEL P A D AND RETAINER 04282 E
-
SPRING NUT 381765.52 (3 REQ'D.) 3 -DEFROSTER OPENING CENTER B E Z E L BRACKET O45E82
A -.SPRING NUT 381765.52 (7 REQ'D.) F
-
SCREW 55927.52 (3 REQ'D.) C
-
SCREW 55907 ( 1 REQ'D.)
B
-
SCREW 55927.52 (7 REQ'D.)
2
-
DEFROSTER OPENING B E Z E L 045094
4 - D E F R O S T E R B E Z E L BRACKET
C
-
C L I P 382228-5 (1 REQ'D.)
J
-
SCREW 55907.52 (2 REQ'D.)
M
-
SCREW 55907.52 (1 REQ'D.)
D
-
NUT AND WASHER ASS'Y. ( I REQ'D.)
K
-
SCREW 55927.52 (1 REQ'D.1
H
-
P A D ASS'Y. LOCATING PIN (PART OF PAD ASS'Y.)
R 1396-A
FIG.
77-Instrument Panel P a d Installation-Falcon
INSTALLATION 4. Lift up the pad. Disconnect taining screws and remove the glove
If the
pad assembly is being re-
the radio speaker wires and the clock box liner.
placed, transfer the radio speaker and
wires. Remove the pad assembly.
2. Reaching through the glove box
the pad retaining clips to the new INSTALLATION
opening, remove the nut which retains
pad assembly.
the pad to the instrument panel (Fig.
1. If the pad is to be replaced, 19).
2' Position the pad to the
transfer the radio.speaker, the clock, 3. Remove the instrument panel
panel' Connect the radio speaker
the instrument control bezel and the
finish moulding retaining =revs and
to the radio.
pad retaining clips to the new pad.
3. Install the pad retaining screws.
remove the moulding.
4. Position the glove compartment
2. Position the pad assembly to
4. Remove the seven screws which
and install the glove compartment re-
the instrument panel. Connect the retain the pad assembly to the instru-
taining screws.
radio speaker and the clock. ment panel. The screws are located as
3. Install the two pad retaining follows: Four in the right side of the
INSTRUMENT PANEL PAD-
screws a t the top of the instrument
pad; two above the instrument cluster;
FAIRLANE
cluster and the seven retaining screws
one a t the left end of the pad. Lift up
REMOVAL
1. Remove the glove box retaining
screws and remove the glove box.
2. Reaching through the glove
box opening, remove two nuts retain-
ing the pad to the panel (Fig. 18).
3. Remove the two pad retaining
screws from the top of the instrument
cluster. Remove the seven pad retain-
ing screws from along the-bottom of
the pad.
along the bottom of the pad.
4. Install the two nuts which re-
tain the pad above the glove compart-
ment.
5. Position the glove compartment
and install the glove compartment re-
taining screws.
INSTRUMENT PANEL PAD-
M O N T E G O
REMOVAL
1.
Remove the glove box liner re-
the pad assembly, disconnect the radib
speaker wires and remove the pad as-
sembly.
INSTALLATION
1. If the pad is to be replaced,
transfer the radio speaker, instrument
panel name plate and the pad retain-
ing clips to the new pad.
2. Position the pad assembly to
the instrument panel and connect the
radio speaker wires.