Ford COUGAR 1968 Shop Manual page 797

PART 17-4
-
Windshield, Window Glass, And Window Mechanisms
VENT WINDOW FRAME,
WEATHERSTRIP, AND/OR
DIVISION BAR-MANUAL
WINDOWS-FAIRLANE
AND MONTEGO
REMOVAL
1.
Remove the door trim panel
and watershield.
2. Remove the inner and outer
door belt line weatherstrips (view
D, Fig. 4) by prying them loose
from the door.
3. Remove the window lower
stop rubber bumper and lower the
door window.
4. Remove the glass front run
adjusting screw, lock nut and washer.
5. Remove the glass front run
from the retainer at the vent frame
by sliding the run down and removing
it from the door through the inner
panel access hole.
6. Remove the three screws re-
taining vent frame to the door
frame. Remove the vent window
assembly and place it on a bench.
7. Remove two screws retaining
the upper vent pivot to the vent
frame assembly. Remove the nut
retaining the lower pivot bolt and
remove the spring, nylon bushings,
washer and stop washer. Remove the
vent window from the frame.
8. Remove two screws from the
top of the assembly and remove the
four rivets retaining the vent frame
and division bar weatherstrip. Sepa-
rate the frame and division bar.
9. If the glass frame is to be re-
placed, remove the glass from the frame
with the tool shown in Fig. 13.
INSTALLATION
1. Install the glass in the frame
with the tool shown in Fig. 13.
2. Position the division bar to
the vent frame. Position the vent
frame and division bar weatherstrip
and install the four rivets and two
screws a t the top of the frame.
3. Assemble the vent
.
tension
spring to the lower pivot and adjust
the pivot spring tension so that the
window will stay open a t highway
speeds.
4. Position the frame assembly on
the door and install the three retain-
ing screws.
5. Position the glass front run in
the door and slide it into the vent
frame retainer.
6. Loosely install the front run
adjusting screw, washer and lock nut.
7. Raise the window halfway and
install the window lower stop rubber
bumper.
8. Adjust the front run and tight-
en the retaining nut.
9. Install the belt line weather-
strips.
10. Install the door watershield
and trim panel.
VENT WIF(DOW FRAME,
WEATHERSTRIP, AND/OR
DIVISION BAR-POWER
WINDOWS-FAIRLANE
AND MONTEGO
REMOVAL
1.
Remove the trim panel and
watershield from the door.
2. Remove two screws attaching
the equalizer arm bracket to the door
inner panel and remove the bracket
(Fig. 3).
3. Disconnect the window regulator
motor wires at the connector.
4. Remove the motor bracket-to-
door inner panel attaching screw
(Fig. 3).
5. Remove the glass lower stop
from the door.
6. Remove the nut and washer from
the vent window division bar lower
adjusting screw (Fig. 3).
7. Remove four screws attaching
the window regulator to the door in-
ner .panel. Support the glass and
channel assembly and lay the regulator
in the bottom of the door.
8. Remove-the front run and retain-
er from the vent window division bar.
9. Remove three screws retaining
the vent window assembly in the door,
and remove the vent window assembly
from the door.
10. Remove two screws retaining
the upper vent pivot to the vent frame
assembly. Remove the nut retaining
the lower pivot bolt and remove the
spring, bushings, and washers. Re-
move the vent window from the
frame.
11. Remove two screws from the
top of the frame and remove four
rivets attaching the frame, weather-
strip, and division bar. Separate the
frame from the division bar.
12.
If the glass frame is to be
replaced, remove the glass from the
frame with the tool shown in Fig.
13.
INSTALLATION
1. Install the glass in the frame
with the tool shown in Fig. 13.
2. Position the division bar to
the vent frame. Position the vent
frame and division bar weatherstrip
to the assembly, and install the four
rivets and two screws a t the top of
the frame.
3. Position the vent glass in the
frame and install the spacer, washer,
spring, bushings, and nut on the low-
er pivot.
4. Install the two screws retain-
ing the vent window upper pivot to
the vent window frame. Then, adjust
the lower pivot tension (SectionZ).
5. Position the vent window as-
sembly to the door and install the
three retaining screws (Fig. 3).
6. Position the front run and re-
tainer into the door. Then, place
the glass in the front and rear runs
and insert the front run into the
vent window division bar.
7. Support the glass and insert
the regulator arm rollers into the
glass channel bracket.
8. Position the window regulator
to the door inner panel and install
the four attaching screws.
9. Insert the regulator arm rol-
lei in the iegulator arm roller
bracket. Position the roller bracket
to the door inner panel and install
the two attaching screws.
10. Install the washer and nut
on the vent window division bar low-
er ad,iusting screw (Fig. 3).
11. Install the motor bracket-to-
door inner panel attaching screw (Fig.
3) and connect the motor wires.
12. Install the window glass low-
er stop and adjust the door window
glass (Section 2).
13. Install. the watershield and
trim panel on the door. Then, clean
the glass and surrounding area.
VENT WINDOW FRAME-
MUSTANG AND COUGAR
REMOVAL
1. Remove the trim panel and water-
shield from the door.
2. Remove two vent window retain-
ing screws (Item B and C, Fig. 5).
3. Remove two lock nuts and set
screws (Items J, K, L, and M, Fig.
5) attaching the vent window and
front run to the door inner panel.
4. Lift the vent window and front
run from the door.
5. Remove the tension nut and
spring from the vent window pivot.
6.
Remove the vent window tension
bracket and remove the vent window
from the frame.
INSTALLATION
1.
Position the vent window to
the frame and install the tension