And 16-** Profibus Parameters - Danfoss VLT Midi Drive FC 280 Programming Manual

Parameters

6.2 9-** and 16-** PROFIBUS Parameters

6.2.1 9-07 Actual Value
9-07 Actual Value
Range: Function:
0 [0 - 65535] This parameter delivers the MAV for a Master
*
Class 2. This parameter is valid if the control
priority is set to Master Class 2.
9-15 PCD Write Configuration
Array [10]
Option: Function:
Select the parameters to be assigned to PCD 3-10 of
the telegrams. The number of available PCDs depends
on the telegram type. The values in PCD 3-10 are then
written to the selected parameters as data values.
Alternatively, specify a standard PROFIBUS telegram in
parameter 9-22 Telegram Selection.
9-16 PCD Read Configuration
Array [10]
Option: Function:
Select the parameters to be assigned to PCD 3–10 of
the telegrams. The number of available PCDs depends
on the telegram type. PCDs 3–10 contain the actual
data values of the selected parameters. For standard
PROFIBUS telegram, see parameter 9-22 Telegram
Selection.
9-22 Telegram Selection
Option: Function:
This parameter shows the selected
standard PROFIBUS telegram that
the PROFINET IO controller has sent
to the frequency converter. At
power-up, or if a non-supported
telegram is sent from the IO
controller, this parameter shows
None in the display.
[1] Standard telegram
1
[100] None
*
[101] PPO 1
[102] PPO 2
[103] PPO 3
[104] PPO 4
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
MG07F102
Programming Guide
9-23 Parameters for Signals
Array [1000]
Read only
Option:
[0]
*
[302]
[303]
[312]
[341]
[342]
[351]
[352]
[380]
[381]
[412]
[414]
[416]
[417]
[553]
[558]
[590]
[593]
[615]
[625]
[696]
[748]
[890]
[891]
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor current
[1615] Frequency [%]
[1616] Torque [Nm]
[1618] Motor Thermal
Danfoss A/S © 05/2016 All rights reserved.
Minimum Reference
Maximum Reference
Catch up/slow Down Value
Ramp 1 Ramp Up Time
Ramp 1 Ramp Down Time
Ramp 2 Ramp Up Time
Ramp 2 Ramp Down Time
Jog Ramp Time
Quick Stop Ramp Time
Motor Speed Low Limit [Hz]
Motor Speed High Limit [Hz]
Torque Limit Motor Mode
Torque Limit Generator Mode
Term. 29 High Ref./Feedb. Value
Term. 33 High Ref./Feedb. Value
Digital & Relay Bus Control
Pulse Out 27 Bus Control
Terminal 53 High Ref./Feedb. Value
Terminal 54 High Ref./Feedb. Value
Terminal 42 Output Bus Control
PCD Feed Forward
Bus Jog 1 Speed
Bus Jog 2 Speed
Function:
This parameter
contains a list of
signals available for
selection in
parameter 9-15 PCD
Write Configuration
and
parameter 9-16 PCD
Read Configuration.
6
39
6