Jeep Cherokee 1999 Electronic Service Manual page 1444

X J
DI SASSEM BLY AN D ASSEM BLY (Cont inue d)
NOTE: If end play is incorrect, transmission is
incorrectly assembled,
washer and/or thrust plate are worn and need to be
changed.
(a ) At t a ch dia l in dica t or (C-3339) t o con ver t er
h ou sin g. P osit ion in dica t or plu n ger a ga in st in pu t
sh a ft a n d zer o in dica t or.
(b) Move in pu t sh a ft in a n d ou t a n d r ecor d r ea d-
in g. E n d pla y sh ou ld be 0.56 - 2.31 m m (0.022 -
0.091 in .).
Fig. 113 Checking Input Shaft End Play
(47) P osit ion t r a n sm ission on wor k su r fa ce wit h
pa n fa ce u pwa r d.
(48) In st a ll va lve body.
(49) Adju st fr on t a n d r ea r ba n ds.
(50) In st a ll flu id filt er a n d pa n .
(51) In st a ll r ea r ext en sion h ou sin g.
(52) In st a ll t or qu e con ver t er.
OVERRUNNING CLUTCH/LOW-REVERSE DRUM
DISASSEMBL Y
(1) If t h e clu t ch a ssem bly ca m e ou t wit h t h e low-
r ever se dr u m , t h r ea d t wo clu t ch ca m bolt s in t o t h e
ca m . Th en lift t h e ca m ou t of t h e dr u m wit h t h e bolt s
(F ig. 114). Rot a t e t h e ca m ba ck a n d for t h t o ea se
r em ova l if n ecessa r y.
(2) Rem ove t h e clu t ch r oller a n d spr in g a ssem bly
fr om t h e over r u n n in g clu t ch r a ce.
ASSEMBL Y
(1) Assem ble clu t ch r oller s a n d spr in gs in r et a in er
if n ecessa r y (F ig. 115).
(2) In st a ll over r u n n in g clu t ch r oller, spr in g a n d
r et a in er a ssem bly in clu t ch ca m (F ig. 116).
(3) Tem por a r ily a ssem ble a n d ch eck over r u n n in g
clu t ch oper a t ion a s follows:
(a ) Assem ble ca m a n d clu t ch .
or output shaft thrust
TRANSMISSION AND TRANSFER CASE
Fig. 114 Removing Overrunning Clutch From
Low-Reverse Drum
(b) In st a ll clu t ch a ssem bly on low-r ever se dr u m
wit h t wist in g m ot ion (F ig. 117).
(c) In st a ll dr u m -clu t ch a ssem bly in ca se a n d
in st a ll clu t ch ca m bolt s.
(d) In st a ll r ea r su ppor t a n d su ppor t a t t a ch in g
bolt s.
(e) Ch eck low-r ever se dr u m
s h o u ld ro ta te fre e ly in c lo c k w is e d ire c tio n
a n d lo c k w h e n tu rn e d in c o u n te rc lo c k w is e
d ire c tio n (a s v ie w e d fro m fro n t o f c a s e ).
Fig. 115 Overrunning Clutch Rollers, Springs,
FRONT SERVO PISTON
DISASSEMBL Y
(1) Rem ove sea l r in g fr om r od gu ide (F ig. 119).
(2) Rem ove sm a ll sn a p r in g fr om ser vo pist on r od.
Th en r em ove pist on r od, spr in g a n d wa sh er fr om pis-
t on .
r ot a t ion . D ru m
Retainer
21 - 121