Jeep Cherokee 1999 Electronic Service Manual page 1317

19 - 6 STEERING
REM OVAL AN D I N STALLAT I ON (Cont inue d)
(14) Rem ove t h e left en gin e m ou n t t h r ou gh bolt n u t
on ly. Do n ot r em ove t h e bolt a t t h is t im e.
(15) Rem ove t h e r em a in in g 2 bolt s fr om t h e
H -Block a n d r em ove t h e H -Block fr om t h e com pr es-
sor.
(16) P osit ion a ja ck st a n d a n d r a ise weigh t off left
en gin e m ou n t .
(17) Rem ove t h e (2) en gin e m ou n t sill pla t e bolt s.
(18) Rem ove t h e (4) en gin e m ou n t br a cket bolt s
fr om t h e en gin e block.
(19) Rem ove t h e en gin e m ou n t t h r ou gh bolt .
(20) Rem ove t h e en gin e m ou n t a n d en gin e m ou n t
br a cket fr om veh icle.
(21) Rem ove t h e (2) power st eer in g pu m p r et a in in g
n u t s (F ig. 10).
Fig. 10 Power Steering Pump
(22) Slide pu m p off m ou n t in g st u ds a n d posit ion so
pr essu r e lin e ca n be r em oved. Th is will r equ ir e you
t o in st a ll pr essu r e lin e on t h e n ew pu m p pr ior t o
in st a llin g it in t h e en gin e block.
(23) Rem ove t h e power st eer in g pu m p fr om t h e
veh icle.
Installation
WARNING: Power steering system fluid may be
contaminated with metal shavings, overheated or
improper fluid. All fluid should be drained from the
system. After component replacement, system
should be flushed and filled with Mopar Power
Steering Fluid, or equivalent.
(1) In st a ll t h e pr essu r e lin e on pu m p in or igin a l
posit ion .
(2) Tr a n sfer t h e dr ive cou pler t o n ew pu m p lea vin g
pin ch bolt lose a t t h is t im e (F ig. 11).
(3) In st a ll t h e power st eer in g pu m p in t h e en gin e
block. Tor qu e r et a in in g n u t s t o 24 N·m (18 ft . lbs.)
(F ig. 11).
Fig. 11 Power Steering Pump
(4) In st a ll t h e en gin e m ou n t a n d en gin e m ou n t
br a cket in veh icle.
(5) In st a ll t h e en gin e m ou n t t h r ou gh bolt a n d lea ve
loose a t t h is t im e.
(6) In st a ll, do n ot t or qu e en gin e m ou n t sill pla t e
n u t s a n d bolt s.
(7) In st a ll (4) en gin e m ou n t br a cket t o en gin e
block r et a in in g bolt s a n d Tor qu e t o 61 N·m (45 ft .
lbs.).
(8) Tor qu e t h e en gin e m ou n t sill pla t e n u t s t o 41
N·m (30 ft . lbs.).
(9) Tor qu e t h e en gin e m ou n t sill pla t e bolt s t o 41
N·m (30 ft . lbs.).
(10) Rem ove ja ck st a n d.
(11) In st a ll t h e H -Block on t h e A/C com pr essor in
t h e or igin a l posit ion a n d lea ve bolt s loose a t t h is
t im e.
(12) P osit ion a n d in st a ll A/C com pr essor.
(13) Slide t h e dr ive cou pler in t o it s or igin a l posi-
t ion a n d st a r t r em a in in g (2) H -Block bolt s.
(14) In st a ll t h e power st eer in g pu m p pu lley (F ig.
12). Tor qu e n u t t o 166 N·m (120 ft . lbs.).
X J