Related Manuals for Extron electronics XTP R HWP 201
Summary of Contents for Extron electronics XTP R HWP 201
- Page 1 User Guide XTP Systems XTP R HWP 201 XTP Receiver – Decorator-Style Wallplate 68-2339-01 Rev. E 01 19...
- Page 2 Safety Instructions Safety Instructions • English Istruzioni di sicurezza • Italiano AVVISO: Il simbolo, , se usato sul prodotto, serve ad avvertire l’utente WARNING: This symbol, , when used on the product, is intended to della presenza di tensione non isolata pericolosa all’interno del contenitore alert the user of the presence of uninsulated dangerous voltage within the del prodotto che può...
- Page 3 より 『Extron Safety www.extron.com and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください。 Copyright © 2017-2019 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks ( ), registered service marks ( ), and trademarks (™) are the property of RGB Systems, Inc.
- Page 4 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 5 Conventions Used in this Guide Notifications The following notifications are used in this guide: Potential risk of severe injury or death. WARNING: AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.
-
Page 7: Table Of Contents
UL Listed Metal Junction Box Installation ..7 Rear and Side Panel Connectors ......8 XTP System Configuration Software ..24 Mounting the XTP R HWP 201 ......9 Software Installation........... 24 Front Panel Connectors ........10 Software Download Center Page ....24 Connection Details .......... - Page 8 XTP R HWP 201 Wallplate Receiver • Contents viii...
-
Page 9: Introduction
XTP matrix switcher (see Power Connection on page 14). To configure and control the XTP R HWP 201, connect a host device, such as a computer, through the USB Config port and enter Simple Instruction Set (SIS) commands (see Configuration and Control... -
Page 10: System Compatibility
The following diagram shows one way the XTP R HWP 201 can be integrated in an XTP point-to-point application. The transmitter can also be used with an XTP matrix switcher (see the XTP matrix switcher user guide for more details on matrix applications and configuration). - Page 11 HDMI audio de-embedding — Supports digital HDMI audio de-embedding as a balanced or unbalanced analog stereo signal on a captive screw connector. • Remote power capability — Allows the XTP R HWP 201 to be powered by an XTP CrossPoint Matrix Switcher or XTP Power Injectors to simplify integration. •...
-
Page 12: Installation
• • Connection Details Installation Overview The XTP R HWP 201 can be installed into the provided mud ring or an optional UL Listed metal electrical junction box. ATTENTION: • Do not mount multiple devices adjacent to each other in the same metal junction box. -
Page 13: Metal Junction Box Or Mud Ring Installation
Route and connect cables to the rear and side panel connectors (see Rear and Side Panel Connectors on page 8). Mount the XTP R HWP 201 to the mud ring or metal junction box (see Mounting the XTP R HWP 201 on page 9). -
Page 14: Mud Ring Installation
Backing Clip Backing Clip 0.75" #6-32 Screw 1.25" #6-32 Screw Layout A Layout B Figure 3. Backing Clip Installation Use a cross-head (Phillips) screwdriver to fasten the screws and backing clips in place. XTP R HWP 201 Wallplate Receiver • Installation... -
Page 15: Ul Listed Metal Junction Box Installation
Le blindage tressé et le blindage en aluminium devraient être connectés à la masse d’un équipement à l’autre bout du câble. XTP R HWP 201 Wallplate Receiver • Installation... -
Page 16: Rear And Side Panel Connectors
Rear Panel Connectors XTP Input connector — Connect a twisted pair cable to the RJ-45 connector labeled “XTP IN” on the XTP R HWP 201 and the XTP output port on another XTP device to pass all signals (see TP Cable Termination and Recommendations on page 12). -
Page 17: Mounting The Xtp R Hwp 201
Figure 7. Installing the XTP R HWP 201 in a Metal Junction Box Align the mounting screws on the XTP R HWP 201 with the available holes on the mud ring (see figure 6, ) or metal junction box (see figure 7,... -
Page 18: Front Panel Connectors
(see figure 9 for wiring details). No Ground Here Ring Sleeves Sleeves Do not tin the wires! Ring No Ground Here Balanced Audio Output Unbalanced Audio Output Figure 9. Audio Output Wiring XTP R HWP 201 Wallplate Receiver • Installation... -
Page 19: Connection Details
Connect and pull the tie wraps until they are secure. Do not overtighten. D IO • Connectez et tirez les serre-câbles jusqu’à ce - 2 3 qu’ils soient sécurisés. Ne pas trop serrer. L A N S IG D IO XTP R HWP 201 Wallplate Receiver • Installation... -
Page 20: Tp Cable Termination And Recommendations
Connector Figure 10. TP Cable Termination Supported cables The XTP R HWP 201 is compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. ATTENTION: • Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable to link the XTP products. - Page 21 Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles. • Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners. • Separate twisted pair cables from AC power cables. XTP R HWP 201 Wallplate Receiver • Installation...
-
Page 22: Rs-232 And Ir Over Xtp Communication
Power Supply Output Cord Figure 12. Power Wiring The XTP R HWP 201 can be connected to a local power supply. See the notifications on the next page for local power considerations. XTP R HWP 201 Wallplate Receiver • Installation... - Page 23 La longueur idéale est de 5 mm (3/16 inches). TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out. XTP R HWP 201 Wallplate Receiver • Installation...
- Page 24 Remote power The XTP R HWP 201 can be powered remotely through an XTP Power Injector or through an XTP matrix switcher. ATTENTION: • XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power should be routed outdoors.
-
Page 25: Operation
Reset Mode on the next page). HDMI Audio Switch The XTP R HWP 201 has an HDMI audio switch (see figure 14, ) that mutes or enables the embedded audio on the HDMI output connector. If necessary, remove the wallplate to access the switch. -
Page 26: Audio Output Overview
DO mistake, cycle power to NOT operate the firmware the device to return to the version that results from this firmware version running prior mode reset. to the reset. XTP R HWP 201 Wallplate Receiver • Operation... -
Page 27: Side Panel Indicators
Power LED indicator — Lights when power is applied to the device. • Signal LED indicator — Lights when an active XTP video signal is received. • Audio LED indicator — Lights when embedded audio output is enabled. • XTP R HWP 201 Wallplate Receiver • Operation... -
Page 28: Sis Configuration And Control
Error Responses When the XTP R HWP 201 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the receiver returns an error response to the host. -
Page 29: Using The Command And Response Tables For Sis Commands
= Carriage return with no line feed = Pipe (can be used interchangeably with the character). • = Space = Escape key = Can be used interchangeably with the character. XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control... -
Page 30: Command And Response Tables For Sis Commands
0 = unmute all audio outputs (default) = Audio mute = Mute the HDMI audio output = Mute the analog audio output = Mute the HDMI and analog audio output XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control... -
Page 31: Advanced Configuration Commands
= Signal status = video or TMDS detected = no sink device detected = HDCP status = sink detected with no HDCP encryption = sink detected with HDCP encryption XTP R HWP 201 Wallplate Receiver • SIS Configuration and Control... -
Page 32: Xtp System Configuration Software
XTP System Configuration Software This section contains installation and configuration procedures for the XTP System Configuration Software for configuring and controlling the XTP R HWP 201. Topics in this section include: • Software Installation Software Operation • Software Installation The XTP System Configuration Software is available for download on the Extron website, www.extron.com. -
Page 33: Software Product Page
Open the executable (.exe) file from the save location. Follow the instructions that appear on the screen. By default, the installation creates a directory in the Program Files or Program Files (x86) folder. XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software... -
Page 34: Software Operation
Software Operation The XTP R HWP 201 can be controlled directly from the front panel configuration port (see figure on page 10) or remotely from an XTP matrix switcher. Connections The XTP System Configuration Software opens to the screen. This screen is Connections used to establish communication with an XTP device through USB connection. -
Page 35: Menu Bar
Backup and Restore Commissioning Report available when directly connected to the device. See an XTP matrix switcher user guide (www.extron.com) for more information on these features. XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software... - Page 36 This option resets all disabled confirmation dialogs to the default settings. From the menu, select . The Tools Software Preference Software Preference dialog box opens. Figure 25. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software...
- Page 37 This option opens the XTP System Configuration Software help file in a Web browser. From the menu, select Help Help Extron Website This option opens the Extron website in a Web browser. From the menu, select Help Extron Website XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software...
-
Page 38: Device Settings
NOTE: 0 dB = 100% volume and -64 dB = 0% volume. If a display is connected through a DVI connection, click the check box below the slider to output analog audio. Analog Audio Volume XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software... - Page 39 XTP R HWP 201. Analog Audio — Displays the mute status of the analog audio output. Analog Audio Volume — Displays the analog audio output volume level in a percentage. XTP R HWP 201 Wallplate Receiver • XTP System Configuration Software...
-
Page 40: Reference Information
CUT-OUT AREA FOR WALL MOUNT Top Panel Figure 29. Mounting Template for 2-Gang Mud Rings (Not to Full Scale) Please measure the printed template before cutting. NOTE: Measure the template before cutting. XTP R HWP 201 Wallplate Receiver • Reference Information... - Page 41 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.