Grouting - Flowserve VTP User Instructions

VERTICA
Examp ple of pump m mounted on a
4.3.3 Leve eling of pum mps with the s
The suction barrel [315] is
and aligned with the anch hor bolts. The
flange is leve eled by using
precision ma achinist's leve el. Levels sho
the equipme ent mounting s
flange moun ting surface n
0.16 mm/m ( (0.002 in./ft) u
the grout to s set for at leas st 72~80 hour
pump is insta alled. Rechec
surface leve lness after the
proceed with h the pump in
assembly [10 01] into the ba
discharge he ead flange bo olt holes to the
[372].
Check to ma ake sure that t
respect to th e barrel flang ge to within 0.
(0.002 in./ft) and final torq que the nuts [
leveling data a is to be reco orded for futur
Example of a a pump install
Page 23 of 7 76
AL TURBINE E PUMPS (VT
soleplate
suction barre
s first lowered d into the pit
suction barre
a master lev el or a
uld be taken o
surfaces. The e suction barre
needs to be le eveled to with
using shims a and grout. Allo
rs before the
ck the barrel m mounting
e grout is set and then
stallation. Low wer the pump
arrel and alig n the
e flange bolts
the pump is s still level with
16 mm/m
373]. The
re reference.
ed with a suc tion barrel.
TPS) CENTRI IFUGAL PUM
4.3.4 Leveling o
mounted o
The so oleplate [23] is
and ali igned with the
suction n barrel [315]
anchor r bolts. Torqu
solepla ate. The suct
using a a master leve
Levels s should be ta
surface es. The suctio
needs to be leveled
in./ft) u using shims
Allow t the grout to s
the pu mp is installe
surface e levelness a
procee ed with the pu
assem mbly [101] into
el
discha arge head flan
[372].
el
Chec ck to make su
resp pect to the ba
on
(0.0 002 in./ft) and
el
leveli ing data is to
hin
ow
Exam mple of pump w
p
4.4

Grouting

G
Where e applicable, g
After a adding pipe w
the cou upling alignm
should d then be grou
engine eering practice
Flowse erve service c
MPS ENGLIS SH 71569224
of pumps with h suction ba
on a soleplat te
s first lowered d onto the fou
e anchor bolts s. Then, lowe
into the pit a nd aligned wi
ue nuts to sec cure suction b
tion barrel fla nge is leveled
el or a precisio on machinist's
aken on the eq quipment mo
on barrel flan ge mounting
d to within 0.1 6 mm/m (0.0
s and grout u under the sol
et for at least t 72~80 hours
ed. Recheck th he barrel mou
after the grout t is set and th
ump installatio on. Lower the
o the barrel an nd align the
nge bolt holes s to the flange
ure that the pu ump is still lev
arrel flange to within 0.16 m
d final torque the nuts [373
be recorded for future refe
with a suction barrel mount
soleplate
grout in the fo oundation bolt
work connectio ons and re-ch
ment, the mou nting plate/so
uted in accord dance with go
e. If in any d oubt, please
center for adv vice.
flowse
4 – 02-15
arrel
undation
er
ith the
barrel to
d by
s level.
unting
surface
002
leplate.
s before
unting
en
e pump
e bolts
vel with
mm/m
3]. The
erence.
ted on a
ts.
hecking
oleplate
ood
contact
erve.com