Performance And Operation Limits; Installation; Location; Preparation - Flowserve VTP User Instructions

VERTICA
3.3.8 Acc essories
Accessories may be fitted d when specif
customer.
3.4 Perfo ormance an
This product has been sele
specifications s of the purcha
The following g data is includ
help with the installation. It
temperature, materials and
data. If requi red, a definitive
application ca an be obtained d from Flowser
3.4.1 Ope erating limits
Pumped liquid d temperature
limits*
Maximum amb bient
temperature*
Maximum pum mp speed
*Subject to w written agreem
Special desig gns and mate
pumps opera ating above a and below the
limits. Conta act Flowserve e for upgrade
available for your specific c application.
4 INSTA ALLATION
Equipm ment operated
must comply y with the rele evant explosio
regulations. See section
potentially ex xplosive atmo
4.1 Loca tion
When equipm ment has been
months, a co omplete inspec
accordance w with section 2.
located to allo ow room for a
maintenance e and inspectio on with ample
lifting and sho ould be as clo ose as practica
supply of liqu uid to be pump ped. Refer to t
arrangement t drawing for th
4.1.1 Insp pection prior
Six months p prior to the sch
Flowserve P ump Division
employed to conduct an in
and the facili ty. If any dete
noticed, the F Flowserve Pu
may require a partial or co omplete disma
equipment in ncluding resto
some compo onents.
Page 21 of 7 76
AL TURBINE E PUMPS (VT
fied by the
nd Operati ion Limits
ected to meet the
ase order. Se ee section 1.5.
ed as addition nal information
is typical and factors such a
seal type may y influence this
e statement fo or your particul
rve.
5 ºC (40 ºF) to + +80 ºC (176 ºF)
Up to +40 ºC (10 04 ºF)
refer to the nam meplate
ment from Flo owserve.
erials may be available for
se specified
options
d in hazardou us locations
on protection
1.6.4, Produc
cts used in
ospheres.
n in storage fo or greater than
ction should be e conducted in
.4.3. The pum p should be
ccess, ventila tion,
headroom for
able to the
the general
he pump set.
to installatio on
heduled instal llation date, a
representativ e is to be
nspection of th he equipment
erioration of e equipment is
mp Division r representative
antling of the
ration and rep placement of
TPS) CENTRI IFUGAL PUM
4.2 Preparatio P
The pu ump should be
ventilat tion, maintena
headro oom for lifting a
practic cable to the su
Refer t to the general
to dimens sions and deta
as
s 4.2.1 General ins
ar The fo ollowing check
actual

installation.

a) Ma ake sure that
po ower supply sy
b) Ch heck the sum
up p.
c) Ch heck the liquid
d) Ch heck the insta
wil ll safely hand
e) Ch heck all pump
an ny shipping an
Alwa
three p places when l
should d be attempted
necess sary for a suc

On n hollow shaft
ag gainst the sha
clu utch

On n solid shaft d
n 6
ag gainst the cou
n
App
r
male s shaft threads
shaft c connection. E
avoide ed.
Alwa
connec cting driver to
improp per motor dire
to the p pump.
e
4.3 F Foundatio
The
pump units to their
depend ds on the size
vibratio on limitations
MPS ENGLIS SH 71569224
on
e located to al low room for a
ance and insp ection with am
and should be e as close as
pply of liquid t to be pumped
arrangement drawing for th
ails.
stallation ch heck-list
ks should be made before
motor namep plate ratings a
ystem match correctly.
p depth and p pump length m
d level in the sump.
allation equipm ment to be su
dle the pump w weight and si
p connections s (bolts, nuts e
nd handling re elated problem
ays support s shafting in at l
lifting or insta alling. No inst
d without adeq quate equipm
cessful install lation.
t drivers, chec ck the clutch
aft size, which h must go thro
drivers, check k the motor sh
upling bore siz ze
ly thread lubr ricant sparing
only at the tim me of making
Excess lubrica ant should be
ays check mo otor rotation be
o pump. Rese erve rotation d
ection can cau use extensive
n/Anchor B Bolts
re are many m methods of in
foundations. The correct m
e of the pump p unit, its loca
. Non-compl iance with the
flowse
4 – 02-15
access,
mple
.
he pump
starting
and the
match-
ure that it
ze.
etc) for
ms.
least
tallation
ment
size
ough the
haft size
ly to
up
e
efore
due to
damage
nstalling
method
ation and
e
erve.com