Flowserve VTP User Instructions page 26

VERTICA
See section 4 4.4.4 for coup pling installatio
shaft drivers and section 4
leveling deta ils.
4.5.2 Insta allation of pu
fully y assembled
4.5.2.1
Lif fting
See lifting m ethods in sec
4.5.2.2
Eq quipment and
ins stallation of a
a) Mobile c rane capable
entire we eight of the pu ump and moto
b) Cable sli
ings for attach
lifting eye es.
c) Ordinary
y hand tools: P Pipe wrenches
wrenche es, socket set,
wrenche es, wire brush,
cloth.
d) Thread s
sealing compo
connecti on and light m machinery oil.
Th e single most
vibration is fr rom a bent sh
straightened to stringent t
and great ca are must be ex
Always supp port shafting in
lifting or insta alling.
Parts and
inside shippi ng containers
individual pa ackages.
Inspect all co ontainers, cra ates and skids
parts before discarding.
Lifting heavy y objects is da
appropriate t tools and proc
4.5.2.3
Un ncrating and
as sembled pum
a) Clean th e parts of all d
other for eign matter.
b) Flush the e pump inside e and outside
water.
c) Clean all l machined su
spots fou und on the ma
emery cl oth.
d) Clean all l threaded con
equipme ent.
Page 26 of 7 76
AL TURBINE E PUMPS (VT
on on solid
4.2.1~4.2.4 fo or pump
umps that ar re shipped
ction 2.3.
d tools requi ired for
a fully assem mbled pump
of hoisting an nd lowering th
or.
hing to the pum mp and motor
s, end
screwdrivers s, Allen
, scraper and fine emery
ound designed d for type of
t common cau use of pump
haft. Shafting g is
tolerances pri ior to shipping
xercised in its s handling.
n at least thre ee places whe
accessories may be place
s, or attached d to skids in
s for attached
angerous. Us se of
cedures is mu ust.
cleaning of a fully
mp
dirt, packing m material and
with clean
urfaces. Rem move any rust
achined surfac ces with fine
nnections and d any accesso
TPS) CENTRI IFUGAL PUM
4.5.2.4 4
Installing
If a bas se plate is use
m (0.00 02 in. per ft),
See se ections 4.2.1~
Positio on lifting equip
founda ation opening.
Sum
thorou ghly cleaned
installa ation.
he
Set up p installation u
r
centere ed directly ov
the bow wl assembly
Lower the bowl ass
the cla amps or holdin
on a fla at surface. T
and red duce possibili
a) Wh hen installing
pu ump assembly
fas stened to the
bo owl assembly
b) Lif ft the pump to
g
us sed, attach it to
c) Po osition pump o
the e discharge of
en
the en lower onto
d) If a a stuffing box
inc cluded, attach
(le eft hand thread
ed
e) If a a mechanical
thi s point per the
If the p pump includes
d
proced dure as listed
section n 2.3)
a) Ins stall the suctio
mo ounting flange
fou undation.
b) If s soleplate is us
so oleplate and m
so oleplate.
c) Le evel the solep
req quired.
d) Ch heck to ensur
an nd other foreig
e) Ins stall the pump
ory
MPS ENGLIS SH 71569224
g the fully as ssembled pum
ed, level the p plate to 0.16 m
grout and anc chor in place.
~4.2.4 for pum mp leveling det
pment so it wil ll center over
.
mp and piping g should be
of all loose d debris before
unit so that th e lifting cable
ver the well or r sump. Care
and suction b barrel with a c
sembly into th e well or sum
ng device tha at is attached
This is to stabi lize bowl asse
ity of cross th reading the sh
152 mm (6 in n.) or 203 mm
y, leave the pu ump securely
wooden skid (as shipped)
is raised to a vertical positi
o a vertical pos sition. If a stra
o the bowl as sembly.
over sump or suction barre
f the pump wi ith external pi
the base. Le evel the entire
and a hollow shaft driver a
h the head sha aft to the pum
ds).
seal is includ ed, install the
e attached ins structions.
s a suction ba arrel (can), fo
below. (See lifting instruct
on barrel first t and grout the
e and bolts di irectly to the
sed, mount a and grout the
mount the suc ction barrel on
plate & the suc ction barrel fla
re suction bar rrel is free of d
gn material.
p.
flowse
4 – 02-15
mp
mm per
tails.
the
starting
e will be
efully lift
clamp.
mp. Set
to bowls
embly
haft.
(8 in.)
until the
on
ainer is
l. Align
ping
e pump.
are
mp shaft
e seal at
ollow the
tions in
e
nto the
ange as
debris
erve.com