Introduction And Safety; General; Ce Marking And Approvals; Disclaimer - Flowserve VTP User Instructions

VERTICA
1 INTRO ODUCTION N AND SAF
1.1 Gene eral
These instructions s must alway
close to the e product's o operating loc
directly with h the produc ct.
Flowserve p roducts are d
manufacture ed with state-o
modern facil ities. The un
care and com mmitment to c
utilizing soph histicated qua ality technique
requirements s.
Flowserve is s committed to
improvemen t and being a at service for a
information a about the prod
operation or about its sup pport products
diagnostic se ervices.
These instru ctions are int
familiarizatio on with the pro
Operating th e product in c
instructions i is important to
service and a avoid risks. T
take into acc count local reg
regulations a are observed
installing the e product. Alw
activity with o operations pe
safety requir rements and a
laws and reg gulations.
These e instructions
installing, o operating, us sing and main
equipment i in any region
equipment m must not be
the conditio ons relating t
instructions s, have been
and apply th he present u user instructi
considered to be misus
product dam mage, delay
misuse are not covered d by the Flow
warranty.
1.2 CE M Marking and
It is a legal re equirement tha
put into servic ce within certa
conform with the applicable
covering Mac chinery and, w where applicab
Equipment, E Electromagnet
Pressure Equ uipment Direc ctive (PED) and
Potentially Ex xplosive Atmo ospheres (ATE
Where applic cable the Direc
Approvals co over important
machinery an nd equipment
Page 4 of 76 6
AL TURBINE E PUMPS (VT
FETY
ys be kept
cation or
esigned, dev eloped and
of-the-art tech hnologies in
it is produced d with great
continuous qu uality control,
es, and safety
o continuous quality
any further
duct in its ins tallation and
s, repair and
ended to faci litate
oduct and its permitted use
compliance w with these
o help ensure e reliability in
The instructio ons may not
gulations; ens sure such
by all, includi ing those
ways coordina ate repair
ersonnel, and follow all pla
applicable saf fety and healt
s must be rea ad prior to
ntaining the
n worldwide. . The
put into serv vice until all
to safety not ted in the
met. Failure e to follow
ions is
e. Personal injury,
or failure ca used by
wserve
d Approva als
at machinery a and equipmen
ain regions of the world sha
e CE Marking Directives
ble, Low Volta
tic Compatibili ity (EMC),
d Equipment f
EX).
ctives and any y additional
safety aspect ts relating to
and the satisf factory provisio
TPS) CENTRI IFUGAL PUM
of tech hnical docume
applica able this docum
relevan nt to these Dir
To con nfirm the Appro
CE ma arked, check th
and the e Certification
1.3 D

Disclaimer

Inform mation in thes
to be c complete an
all of t the efforts of
provid de comprehe
y
engine eering and s
used.
Flowse erve manufact
Interna ational Quality
as cert tified and audi
organiz zations. Genu
been d designed, teste
produc cts to help ens
and pe erformance in
parts a and accessorie
e.
incorre ect incorporatio
may ad dversely affec
feature es of the produ
install o or use authori
access sories is consi
failure caused by mi
Flowse erve warranty.
ant
Flowse erve products
th
may im mpair the safet
1.4 C

Copyright

All righ hts reserved.
be rep produced, stor
transm mitted in any fo
permis ssion of Flows
1.5 Duty Cond D
This pr roduct has be
specifi cations of you
acknow wledgement o
separa ately to the Pu
with th hese instructio
The product T
nt
the pa arameters sp
ll
there i is any doubt
produ uct for the ap
ge
Flows serve for adv
for
If the c conditions of s
are go oing to be cha
tempe rature or duty
seeks the written ag
start u p.
on
MPS ENGLIS SH 71569224
ents and safety y instructions.
ment incorpor rates informati
rectives and A Approvals.
ovals applying g and if the pro
he serial numb ber plate mark
. (See section n 9, Certificatio
r
se User Instr ructions is b
d reliable. H However, in s
f Flowserve Corporation
ensive instru uctions, good
safety practic ce should alw
tures products s to exacting
Management t System Stan
ted by externa al Quality Ass
uine parts and d accessories
ed and incorpo orated into the
sure their cont inued product
use. As Flow wserve cannot
es sourced fro om other vend
on of such par rts and access
ct the performa ance and safe
ucts. The failu ure to properly
zed Flowserve e parts and
dered to be m misuse. Dama
suse is not co overed by the
. In addition, a any modificatio
or removal of f original comp
ty of these pro oducts in their
No part of th hese instructio
red in a retrie val system or
orm or by any y means with
serve.
ditions
een selected t to meet the
ur purchase o order. The
of these cond ditions has be
urchaser. A c copy should b
ons.
must not be e operated be
pecified for th he applicatio
t as to the su uitability of th
pplication int tended, conta
vice, quoting the serial nu
service on yo our purchase o
anged (for exa ample liquid p
y) it is request ted that the u
greement of F Flowserve bef
flowse
4 – 02-15
Where
on
oduct is
kings
on.)
believed
spite of
to
d
ways be
ndards
urance
have
e
t quality
test
ors the
sories
ety
y select,
age or
on of
ponents
use.
ons may
r
out prior
een sent
be kept
eyond
on. If
he
act
umber.
order
pumped,
user
fore
erve.com