GE Interlogix Concord Express Installation Instructions Manual page 20

Phones Menu
The PHONES menu lets you set up central station reporting
for the system (global) and pager reports (partition spe-
cific).
The following describes how to program the settings that
appear under CS PHONE 1-2.
Phone Number
(0100-cs phone 1, 0110-cs phone 2)
(Default = none) This setting is used for programming the
central station receiver phone number. Phone numbers can
be 1 to 24 digits long, including pauses or * and #
characters. To enter pauses, press
7 for one second. To enter #, press and hold 9 for
hold
one second.
œÌi
The PHONE NUMBER menus are not accessible
if a Dealer Code is programmed and the Installer
Code is used to enter installer programming mode.
To access these menus when a Dealer Code is
programmed, you must enter installer program-
ming mode using the Dealer Code.
œÌi
Call-waiting services should be disabled to prevent
interruptions to panel communication to the central
monitoring station (or pager). To program a dialing
prefix that disables call-waiting, see the CALL
WAIT CANCEL setting under the menu PHONE
OPTIONS—GLOBAL.
To program a Central Station Phone Number:
With the display showing PHONE NUMBER _ (or
current number), enter the desired phone number.
The display flashes the entered number. Press
the display shows the new number.
To delete a Central Station Phone Number:
With the display showing PHONE NUMBER (current
D .
number), press
The display shows PHONE NUMBER _.
(Phones—CS Phone 1-2)
C . To enter *, press and
ƒ and
High Level Rpts
(0101-cs phone 1, 0111-cs phone 2)
(Defaults: CS Phone 1 = on, CS Phone 2 = off) When this
setting is on, the panel reports to the central station events
that involve a high-level security risk, including the
following conditions:
q Fire, Police, Auxiliary, Duress, and Freeze alarms
q No Activity
q Receiver Failure (or jam)
q System Tamper (40 incorrect keystrokes or touchpad
supervisory),
q Entering or exiting Sensor Test mode
To turn High-Level Reports off or on:
With the display showing HIGH LEVEL RPTS OFF/
ON (current setting), press
The display flashes the entered setting. Press
the display shows the new setting.
Low Level Rpts
(0102-cs phone 1, 0112-cs phone 2)
(Defaults: CS Phone 1 = on, CS Phone 2 = off) When this
setting is on, the panel reports non-alarm conditions to the
central station, including the following conditions:
q Force Armed
q Hardwire Zone Trouble (open or short)
q Supervisory (wireless devices)
q Low Battery (wireless devices)
q Other non-alarm related conditions
To turn Low-Level Reports off or on:
With the display showing LOW LEVEL RPTS OFF/
ON (current setting), press
The display flashes the entered setting. Press
the display shows the new setting.
Open/Close Rpts
(0103-cs phone 1, 0113-cs phone 2)
(Defaults: all off) When this setting is on, the panel sends a
report when the system is armed (closed) or disarmed
(opened).
œÌi
To use this feature, the OPENING REPORTS and
CLOSING REPORTS settings under the
REPORTING menu must be turned on.
To turn Opening/Closing Reports off or on:
With the display showing OPEN/CLOSE RPTS OFF/
ON (current setting), press
The display flashes the entered setting. Press
the display shows the new setting.
Programming the Panel
(Phones—CS Phone 1-2)
1 (off) or 2 (on).
ƒ and
(Phones—CS Phone 1-2)
1 (off) or 2 (on).
ƒ and
(Phones—CS Phone 1-2)
1 (off) or 2 (on).
ƒ and
17