GE Interlogix Concord Express Installation Instructions Manual page 18

Downloader Code
(0000)
(Default = 12345) The 5-digit downloader code is used in
conjunction with downloader programming. The down-
loader operator must have the panel account number and
downloader code in order to perform any programming.
To program a Downloader Code:
With the display showing DOWNLOADER CODE
nnnnn (current code), enter the desired 5-digit code, +
ƒ . The display flashes the entered code. Press ƒ and
the display shows DOWNLOADER CODE nnnnn (new
code).
œÌi
The Downloader Code cannot be deleted or
cleared from panel memory. To change the Down-
loader Code to its default setting, enter 12345 in
the procedure above.
Installer Code
(0001)
(Default = 4321) The 4-digit installer code is used for
entering program mode and changing system settings. If a
dealer code (see below) is programmed, only those settings
not associated with phone numbers can be changed.
To program an Installer Code:
With the display showing INSTALLER CODE nnnn
(current code), enter the desired 4-digit code +
The display flashes the entered code. Press
display shows INSTALLER CODE nnnn (new code).
œÌi
The Installer Code cannot be deleted or cleared
from panel memory. To change the Installer Code
to its default setting, enter 4321 in the procedure
above.
Dealer Code
(0002)
(Default = none) The 4-digit dealer code is used to prevent
unauthorized persons from changing the programmed
central station phone number. When this feature is enabled,
central station phone numbers cannot be changed (unless
you enter the program mode by using the dealer code). All
other system settings are still accessible by entering the
program mode with the installer code.
To program a Dealer Code:
With the display showing DEALER CODE ****, enter
the desired 4-digit code. The display flashes the
ƒ and the display shows the new
entered setting. Press
code.
To delete a Dealer Code:
With the display showing DEALER CODE nnnn
(current code), press D. The display shows DEALER
CODE ****.
œÌi
The Dealer Code cannot be deleted by clearing
panel memory.
(Security—Global)
(Security—Global)
ƒ .
ƒ and
(Security—Global)
The following describes how to program the security set-
tings that appear under PARTITION 1.
Account Number
(0010)
(Default = 00000) The account number is used as panel (or
customer) identification for the central monitoring station.
The panel sends the account number every time it reports to
the central station. Account numbers must be 1 to 10
characters long.
Alpha characters A-F can be assigned to the account
number by pressing and holding buttons 1-6 respectively
until the character appears.
To program an Account Number:
With the display showing ACCOUNT NUMBER
nnnnn (current number), enter the desired account
number. The display flashes the entered setting. Press
ƒ and the display shows the new number.
Quick Arm
(0011)
(Default = off) Quick Arm allows system arming without
using an access code. When this feature is on, the system
arming level can be increased from Level 1-OFF to LEVEL
2-STAY, from Level 1-OFF to LEVEL 3-AWAY, or from
Level 2-STAY to LEVEL 3-AWAY without entering an
access code. A valid access code is still required to
decrease the arming level or disarm the system.
To turn Quick Arm off or on:
With the display showing QUICK ARM OFF/ON
(current setting), press
The display flashes the entered setting. Press
the display shows the new setting.
Quick Exit
(0012)
(Default = on) This setting determines whether or not users
can open and close a standard entry or exit door without
causing an alarm (while the system is armed). This feature
would be useful if the user wanted to go out to get the
morning paper while the system was armed. This feature
also allows the user to leave the armed premises without
having to disarm and rearm the system.
When this feature is on, pressing
the system is armed) starts a 2-minute timer that allows one
standard entry or exit door (sensor groups 10 and 19 only)
to be activated once (opened, then closed).
When this feature is turned off, the system must be
disarmed before opening any protected door.
œÌi
For UL Listed systems, Quick Exit must be turned
off.
To turn Quick Exit off or on:
With the display showing QUICK EXIT OFF/ON
(current setting), press
The display flashes the entered setting. Press
the display shows the new setting.
Programming the Panel
(Security—Partition 1)
(Security—Partition 1)
1 (off) or 2 (on).
ƒ and
(Security—Partition 1)
D on a touchpad (while
1 (off) or 2 (on).
ƒ and
15