Table of Contents
Advertisement
Thermo: channel N "XXXX"
YYC
of a specified range set by a user
sensor. XXXX – is a description of a temperature sensor, specified by a user at the page of a web interface. YY are readings of a current temperature in
°C. AA is a lower limit of a temperature range in °C. BB – is an upper limit of a temperature range in °C.
Thermo: channel N "XXXX"
YYC
of a range specified by a user
when notifications from a temperature sensor are enabled in the log file
sensor. XXXX – is a description of a temperature sensor, specified by a user at the page of a web interface. YY – are readings of a current temperature
in °C. AA – is a lower limit of a temperature range in °C. BB – is an upper limit of a temperature range in °C.
Thermo: channel N "XXXX" - there is no sensor or it is faulty – is recorded into the log file when a temperature sensor does not respond (is not
connected)
when notifications from a temperature sensor are enabled in the log file N – is a number of a channel of a temperature sensor. XXXX – is a
description of a temperature sensor, specified by a user at the page of a web interface.
Events from a Humidity Sensor
Humidity XX%, normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are within the limits of a range specified by a user
when notifications from a humidity sensor are enabled in the log file. XX – are readings of a relative humidity in %. YY is a lower limit of a normal
humidity in %. ZZ – is an upper limit of a normal humidity range in %.
Humidity XX%, above normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are above the limits of a range specified by
a user
when notifications from a humidity sensor are enabled in the log file
normal humidity range in
%. ZZ is an upper limit of a normal humidity range in %.
Humidity XX%, below normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are below the limits of the range specified
by a user
when notifications from a humidity sensor are enabled in the log file
normal humidity range in
%. ZZ – is an upper limit of a normal humidity range in %.
Humidity - there is no sensor or it is faulty – is recorded in the log file when a humidity sensor does not respond (is not connected) when notifications
from a humidity sensor are enabled in the log file
Events from Smoke Sensors
Smoke sensor N "XXXX" switched to the status "YYYY" – is recorded into the log file when a status of a smoke sensor is being changed when
notifications from a smoke sensor are enabled in the log file. X – is a channel number of a smoke sensor. XXXX is a description of a channel of a smoke
sensor, which is specified by a user at the page of a web interface. YYYY is a name of a current status of a smoke sensor. The next statuses are possible:
«Normal», «ALARM», «Off», «Failure».
Events of the Module «Watchdog»
Watchdog: resetting a channel N "XXXX". A (IPA) YYYY, B (IPB) YYYY, C (IPC) YYYY – is recorded into the log file when the module Watchdo
g
» is triggered
. N – is a number of a power management channel. XXXX – is a description of a power management channel, which is specified by a user
at the page of a web interface. IPA, IPB, IPC – IP addresses specified by a user in the settings of the module «Watchdog» are substituted. YYYY – is a
status, corresponding to a requested IP address. The next statuses are possible:
Watchdog: channel N "XXXX" - a limit of repeated resets is over (Y). Resets are paused. – is recorded into the log file if in the mode of the module
«Watchdog» a limit for the number of consequent resets of a connected device is reached. N – is a number of a power management channel. XXXX - is
a description of a power management channel, specified by a user at the page of a web interface. Y – is a number of consequent resets of a connected
device
.
Watchdog: channel N "XXXX" reset - a response is received. Reset pause is over. – is recorded into the log file if a response from the module «Watchdo
g» is received in the status when
functioning of the watchdog according to a usual algorithm
Events of the Module «Schedule»
Schedule N switched to the status YYYY – is recorded into the log file when the module
channel. YYYY – is a status of an embedded relay. The next statuses are possible: on ,
Events from Embedded Relays
PWR: relay N "XXXX" YYYY – is recorded into the log file when an embedded relay was triggered. N – is a number of a power management channel.
XXXX – is a description of a power management channel, specified by a user at the page of a web interface. YYYY is a status of an embedded relay.
The next statuses are possible:
PWR: relay N "XXXX" is switched to the mode "YYYY" through the web interface – is recorded into the log file when a relay management mode is swi
tched
through a
device web interface. N – is a number of a power management channel. XXXX – is a description of a power management channel,
specified by a user at the page of a web interface. YYYY – is a name of a relay management mode. The next modes are possible: «switched off manually
Copyright © NetPing east Co., Ltd E-mail:
, above normal
(AA
..BBC – is recorded into the log file, when readings of a temperature sensor are above the limits
)
when notifications from a temperature sensor are enabled in the log file
, below normal
(AA
..BBC – is recorded into the log file when readings of a temperature sensor are below the limits
)
.
resets are paused after a specified limit is reached.
.
«switched on» «switched off»
,
.
support@netpingdevice.com
. N – is a number of a channel of a temperature
.
. XX – are readings of a relative humidity in %. YY is a lower limit of a
. XX – are readings of a relative humidity in %. YY – is a lower limit of a
«responds» «silent» «ignored»
,
,
«Wathdog» signals a reset of reboots and a start of a normal
«Schedule» is triggered N is a number of a power management
«
» «off»
.
Phone:+886-2-23121582
. N – is a number of a channel of a temperature
.
.
«
Hide quick links:
Advertisement
Table of Contents
