Table of Contents
Advertisement
KONTRON
Master or Slave Submenus
25.3.1
Feature
Option
Type
None
User
Auto
CD-ROM
IDE Removable
ATAPI Removable
Other ATAPI
Cylinders
1 to 65,536
Heads
1 to 256
Sectors
1 to 63
Maximum Capacity
N/A
Total Sectors
N/A
Maximum Capacity
N/A
Disabled
Multi-Sector Transfer
2 sectors
4 sectors
8 sectors
16 sectors
LBA Mode Control
Disabled
Enabled
Disabled
32-Bit I/O
Enabled
Transfer Mode
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
FPIO 3 / DMA 1
FPIO 4 / DMA 2
Ultra DMA Mode *
Disabled
MOD0
MOD1
MOD2
MOD3
MOD4
MOD5
SMART Monitoring
Disabled
Enabled
Note:
In the Option column, bold shows default settings.
(*)
The CompactFlash IDE interface is not capable of running UDMA modes.
On the 40 pin IDE interface an 80line UDMA 100 cable is
required for proper operation in modes UDMA 3 and higher.
coolMONSTER/PM User's Guide
73
Description
None = Autotyping is not able to supply the drive
type or end user has selected None, disabling any
drive that may be installed.
User = End user supplies hdd information.
Auto = Autotyping. The drive itself supplies the
information.
CD-ROM = CD-ROM drive.
ATAPI Removable = Read- and writeable media
e.g. LS120 and USB-ZIP
Other ATAPI = for ATAPI devices not supported by
other HDD features.
Number of cylinders.
Number of read/write heads.
Number of sectors per track.
Displays the calculated size of the drive in CHS.
Number of total sectors in LBA mode.
Displays the calculated size of the drive in LBA.
Any selection except Disabled determines the
number of sectors transferred per block.
The standard is one sector per block.
Enabling LBA causes Logical Block Addressing to
be used in place of CHS.
Enables 32-bit communication between CPU and
IDE card. Requires PCI or local bus.
Selects the method for transferring the data
between the hard disk and system memory.
Selects the UDMA mode to move data to/from the
drive. Autotype the drive to select the optimum
transfer mode. This feature is autodetected.
Shows whether a disk supports SMART.
Appendix B: BIOS Operation
25.4 Advanced Menu
Feature
Option
8Advanced Chipset Control
Sub menu
8PCI/PNP Configuration
Sub menu
8Memory Cache
Sub menu
8I/O Device Configuration
Sub menu
8Keyboard Features
Sub menu
8Hardware Monitor
Sub menu
8Watchdog Settings
Sub menu
8Display Control
Sub menu
8Miscellaneous
Sub menu
25.4.1
Advanced Chipset Control Submenu
Feature
Option
Enable Memory gap
Disabled
Enabled
Graphics Engine 1
Disabled
Enabled
Graphics Engine 2
Disabled
Enabled
Graphics Memory
UMA = 1MB, 8MB, 16MB, 32MB
Note: In the Option column, bold shows default settings.
Appendix B: BIOS Operation
74
KONTRON
Description
Opens Advanced Chipset Control sub menu.
Opens PCI/PNP Config sub menu.
Opens Cache Control sub menu.
Opens Peripheral Config sub menu.
Opens Keyboard Features sub menu.
Shows hardware monitor current state.
Opens Watchdog Config sub menu.
Opens Display Control sub menu
Opens sub menu with miscellaneous options.
Description
Allows enabling a 1MB memory gap
for add-on cards at 15MB
Enable/Disable Internal Graphics
Device.
Enabled/Disabled Function 1 of the
Internal Graphics Device
Select the amount of main memory
that the Internal Graphics Device will
use.
coolMONSTER/PM User's Guide
Advertisement
Table of Contents
