Applying Effects In Patch Mode - Roland Fantom-Xa Owner's Manual

Adding Effects

Applying Effects in Patch Mode

In Patch mode you can use two multi-effects (MFX1, MFX2), one chorus, and one reverb. Multi-effect 1 (MFX1) will operate according to the effect
settings of the patch or rhythm set assigned to the Keyboard part. Multi-effect 2 (MFX2) will operate according to the effect settings of the patch or
rhythm set assigned to the Pad part. Chorus and reverb will both operate according to the settings of the patch or rhythm set assigned to either the
Keyboard part or the Pad part.
Specifying How the Sound Will Be Output (Routing)
Here you can make overall settings for effects, and the output destination and level of each signal.
fig.Routing
2 7
1
5
8
3
6 9
4
For details on these settings, refer to Making Effect Settings (p. 157).
Parameter Value
Part Select KBD, PAD
1
Tone Select 1–4 (A0–C8)
(Rhythm Key
Select)
Tone Output 0–127
2
Level
Tone Chorus 0–127
3
Send Level
Tone Reverb 0–127
4
Send Level
MFX Type 0–78
5
Patch Output MFX, A, B,
6
Assign 1–4, TONE
Tone Output MFX, A, B,
Assign 1–4
MFX Output 0–127
7
Level
MFX Chorus 0–127
8
Send Level
158
15
12
10
13
14
11
Explanation
Part for which you want to make settings
Tone (or rhythm tone) for which you want to make settings
This parameter is Rhythm Key Select when a rhythm set is being selected. You can select the
rhythm tone (A0–C8) for which you want to make settings.
Level of the signal sent to the output destination specified by Output Assign
Level of the signal sent to chorus for each tone
Level of the signal sent to reverb for each tone
Selects from among the 78 available multi-effects.
For details on multi-effects parameters, refer to Multi-Effects Parameters (p. 164).
Specifies how the direct sound of each patch will be output.
MFX: Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that
passes through multi-effects.
A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in stereo without passing through
multi-effects.
1–4: Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
TONE: Outputs according to the settings for each tone.
This parameter is Rhythm Output Assign when a rhythm set is being selected. You can specifies for
each rhythm set how the direct sound will be output.
* If the Mix/Parallel parameter is set to "MIX," all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 194).
Specifies how the direct sound of each tone will be output.
MFX: Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that
passes through multi-effects.
A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in stereo without passing through
multi-effects.
1–4: Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
* If the Patch Output Assign is set to anything other than "TONE," these settings will be ignored.
• When the Structure Type parameter has a setting of Type "2"–"10," the outputs of tones 1 and 2
will be combined with tone 2, and the outputs of tones 3 and 4 will be combined with tone 4. For
this reason, tone 1 will follow the settings of tone 2, and tone 3 will follow the settings of tone 4 (p.
38).
* If the Mix/Parallel parameter is set to "MIX," all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 194).
Volume of the sound passed through the multi-effects
Amount of chorus for the sound passed through multi-effects