Roland Fantom-Xa Owner's Manual page 171

22: VK ROTARY
This type provides modified response for the rotary speaker, with
the low end boosted further.
This effect features the same specifications as the VK-7's built-in
rotary speaker.
fig.MFX-22
L in
Rotary
R in
Parameter Value
Speed # SLOW, FAST
Brake # OFF, ON
Woofer Slow 0.05–10.00 Hz
Speed
Woofer Fast 0.05–10.00 Hz
Speed
Woofer Trans 0–127
Up
Woofer Trans 0–127
Down
Woofer Level 0–127
Tweeter Slow 0.05–10.00 Hz
Speed
Tweeter Fast 0.05–10.00 Hz
Speed
Tweeter Trans 0–127
Up
Tweeter Trans 0–127
Down
Tweeter Level 0–127
Spread 0–10
Low Gain -15– +15 dB
High Gain -15– +15 dB
Level # 0–127
23: CHORUS
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
fig.MFX-23
Balance D
L in
Chorus
Chorus
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
2-Band EQ
L out
R out
2-Band EQ
Explanation
Rotational speed of the rotat-
ing speaker
Switches the rotation of the
rotary speaker.
When this is turned on, the
rotation will gradually
stop. When it is turned off,
the rotation will gradually
resume.
Low-speed rotation speed of
the woofer
High-speed rotation speed of
the woofer
Adjusts the rate at which the
woofer rotation speeds up
when the rotation is switched
from Slow to Fast.
Adjusts the rate at which the
woofer rotation speeds up
when the rotation is switched
from Fast to Slow.
Volume of the woofer
Settings of the tweeter
The parameters are the
same as for the woofer.
Sets the rotary speaker stereo
image. The higher the value
set, the wider the sound is
spread out.
Gain of the low range
Gain of the high range
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Parameter Value
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate # 0.05–10.00 Hz, note
Depth 0–127
Phase 0–180 deg
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance # D100:0W–
D0:100W
Level 0–127
24: FLANGER
This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
fig.MFX-24
Balance D
L in
Flanger
Feedback
Feedback
Flanger
R in
Balance D
Parameter Value
Filter Type OFF, LPF, HPF
Cutoff Freq 200–8000 Hz
Pre Delay 0.0–100.0 ms
Rate # 0.05–10.00 Hz, note
Depth 0–127
Phase 0–180 deg
Feedback # -98– +98 %
Low Gain -15– +15 dB
High Gain -15– +15 dB
Balance # D100:0W–
D0:100W
Level 0–127
Adding Effects
Explanation
Basic frequency of the filter
Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between the di-
rect sound (D) and the chorus
sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from
when the direct sound begins
until the flanger sound is heard.
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative (-) set-
tings will invert the phase.
Gain of the low range
Gain of the high range
Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Output Level
171