Roland Fantom-Xa Owner's Manual page 125

5.
When you are finished recording, press [
The [ ] indicator will go dark.
If you are not satisfied with the realtime recording you just
made, you can press [ERASE/UNDO] to return to the state
prior to recording. After executing Undo, you can use Redo to
revert to the previous state. After executing Undo, you can
execute Redo by performing the above procedure once again.
Recording Tempo Changes in a
Song (Tempo Recording)
If you want the tempo to change during the song, you can record
those tempo changes in the Tempo track. If tempo changes have
already been recorded in the tempo track, they will be rewritten.
Set the following recording parameters in addition to the basic
3
settings described in step of p. 124.
Parameter Value
Tempo Rec Sw OFF,
ON
You will be able to use REALTIME CONTROL knob
movements to control the tempo easily (p. 121).
Loop Recording and Punch-In
Recording
You can record repeatedly over a specified area (Loop recording), or
re-record just that area (Punch-in recording).
Set the following recording parameters in addition to the basic
3
settings described in step of p. 124.
Parameter Explanation
Loop/ Specify how loop recording or punch-in recording
Punch is to take place.
OFF:
Loop recording or punch-in recording will not oc-
cur.
LOOP (POINT):
Recording takes place repeatedly, according to the
loop point settings.
LOOP (1–16 MEAS):
The 1–16 measure area starting at the record-start
measure will be recorded repeatedly.
LOOP SONG ALL:
The entire song from beginning to end will be re-
corded repeatedly.
AUTO PUNCH:
Auto punch-in recording will be performed.
MANUAL PUNCH:
Manual punch-in recording will be performed.
Start Point Measure and beat at which loop recording or auto
punch-in recording is to begin
* It is not possible to specify the Tick.
End Point Measure and beat at which loop recording or auto
punch-in recording is to Stop.
* It is not possible to specify the Tick.
* The minimum loop length is four quarter notes.
].
Explanation
Specify whether tempo changes will
be recorded (ON), or not (OFF).
Using Auto Punch-In Recording
You must pre-specify the area (punch points) in which recording is
to take place. This is convenient when you want to re-record over a
mistake. The song will play back when you begin recording. When
you reach the punch-in point, playback will switch to record mode.
1.
In the Realtime Rec Standby window, set the Loop/Punch
parameter to "AUTO PUNCH."
2.
Set the Start Point/End Point parameters to the desired
punch points.
3.
Move to a measure earlier than the specified Start Point,
and press [ ] or [F6 (START)].
The song will begin playing. Recording will begin at the
location specified by the Start Point parameter. Playback will
resume at the location specified by the End Point parameter.
4.
Press [ ] to stop playback.
Using Manual Punch-In Recording
Recording takes place (erasing the existing data) in the area that you
specify by pressing a pedal or button. This is convenient when you
want to re-record more than one location in which you made a
mistake. The song will play back when you begin recording. When
you press a pedal or button, playback will switch to record mode,
and will switch back to play mode when you press the pedal or
button once again. By pressing the pedal or button, you can toggle
between record and play modes.
If you want to use a pedal connected to the PEDAL CONTROL
jack to specify the area for recording, you must first set the
Control Pedal Assign parameter to "PUNCH IN/OUT" (p. 195).
1.
In the Realtime Rec Standby window, set the Loop/Punch
parameter to "MANUAL PUNCH."
2.
Press [ ] or [F6 (START)].
Song playback will begin, and the Realtime Rec Control
window will appear.
fig.PunchIn1
3.
At the point where you want to begin recording, press [F3
(PUNCH IN)] or step on the pedal.
Playback will switch to record mode.
fig.PunchIn2
4.
At the point where you want to stop recording, once again
press [F3 (PUNCH OUT)] or step on the pedal.
You will return to playback mode.
5.
Press [ ] to stop playback.
Recording Songs
125