ACME SAM-50 User Manual page 5

DMX 512 Address Setting
Press ENTER button and turn jog wheel until
Pressing ENTER button and the display will blink. Use jog wheel to change the DMX 512
address. Once the address has been selected, press ENTER button to setup or
automatically return to the main functions without any change after 10 seconds. Back to
the previous functions without any change press ESC button.
Slave Mode
Press MENU button until
Slave Mode
button and the display will blink. Use DOWN and UP button to select the (slave1~slave10)
mode. Once the mode has been selected, press ENTER button to setup or automatically
return to the main functions without any change after 10 seconds. Back to the functions
without any change press MENU button again.
Stand By Mode
Press MENU button until
Stand By Mode
button and the display will blink. Use DOWN and UP button to select the (Yes) or (No)
mode. Once the mode has been selected, press ENTER button to setup or automatically
return to the main functions without any change after 10 seconds. Back to the functions
without any change press MENU button again.
Inverse Pan
Press MENU button until
Inversion Pan
button and the display will blink. Use DOWN and UP button to select the (Yes) or (No)
mode. Once the mode has been selected, press ENTER button to setup or automatically
return to the main functions without any change after 10 seconds. Back to the functions
without any change press MENU button again.
is shown on the monitor.
DMX Address
is shown on the display. Pressing ENTER
is shown on the display. Pressing ENTER
is shown on the display. Pressing ENTER
8-
Program Movement
1. Press the ENTER button and turn jog wheel until
on the monitor. Pressing ENTER button and the display will blink. Use jog wheel to
select the (Position) or (speed) or (Time) mode.
2. Select the Pressing ENTER button and the display will blink. Use jog
Position
wheel to select the (Master) or (Slave 2~Slave 10) or (Copy).
3. Select the Pressing ENTER button and the display will blink. Use jog
Master
wheel to select the (Step1~Step6) mode. Select (Yes) option, Use jog wheel to select
the 0~360°. Pressing ENTER button .Back to the main functions, press the ESC
button twice.
4. Select the
Slave 2~Slave 10
Use jog wheel to select the (Step 1~Step 6) mode. Select (Yes) option, Use jog wheel
to select the 0~360°. Pressing ENTER button .Back to the main functions, press the
ESC button twice.
5. Select the Copy Pressing ENTER button and the display will blink. Use jog wheel
to select the (From: Master To: Slave 10 or From: Slave 5 To: Slave 6 or etc) mode.
Select (Yes) option and Pressing ENTER button. Back to the main functions press
the ESC button twice.
6. Select the Pressing ENTER button and the display will blink. Use jog
Speed
wheel to select the (Step 1~Step 6) mode. Select (Speed 1~16) option and Pressing
ENTER button. Back to the main functions press ESC button twice.
7. Select the Pressing ENTER button and the display will blink. Use jog wheel
Time
to select the (Step 1~Step 6) mode. Use jog wheel to select the (0.1s~25.5s). Select
(Yes) option and Pressing ENTER button. Back to the main functions press ESC
button twice.
Test
Press MENU button until is blinking on the display. Pressing ENTER button and
Test
the unit will run self-test by built in program. Back to the functions press MENU button
again.
Fixture Hours
Press MENU button until
Fixture Hours
button and the display will show the number of working hours of the unit. Back to the
functions press MENU button again.
Program Movement
Pressing ENTER button and the display will blink.
is blinking on the display. Pressing ENTER
9-
is shown