CONTENTS 01/ Safety Instructions ....................2 02/ Technical Specifications ..................6 03/ Control Panel ......................8 04/ Fixture Installation ....................9 4.1 Hanging the Fixture ..................10 4.2 Splicing the Fixtures ..................11 05/ How To Set The Unit .................... 14 5.1 Main Functions ....................
01/ Safety Instructions Please read the instruction carefully which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual. Important: Damages caused by the disregard of this user manual are not subject to warranty.
Page 4
off the mains power immediately. DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly. DO NOT touch any wire during operation as there might be a hazard of electric shock. Avoid entanglement of the power cord with other wires. ...
Page 5
01/ Consignes de sécurité Veuillez lire attentivement les instructions qui contiennent des informations importantes sur l'installation, l'utilisation et l'entretien. ATTENTION Veuillez conserver ce guide de l'utilisateur pour une consultation future. Si vous vendez l'appareil à un autre utilisateur, assurez-vous qu'il reçoive également ce manuel d'instructions.
Page 6
pour éviter tout risque d'incendie. Assurez-vous que le cordon d'alimentation n'est pas pincé ou endommagé; remplacez-le immédiatement s'il est endommagé. La température de surface de l'unité peut atteindre 75℃. NE PAS toucher les capots à mains nues pendant son fonctionnement. Évitez que des liquides inflammables, de l'eau ou du métal ne pénètrent dans l'appareil.
02/ Technical Specifications Power Voltage 100-240V~ 50/60Hz Power Consumption 1205W 12x60W RGBW LED 96x3W CW LED Light Source 96x3W WW LED 96x0.5W RGB LED Beam Angle 2.8°-31° Field Angle 5°-46° 0-100% smooth dimming; outstanding strobe effect with variable Dimmer/Strobe speed Tilt Movement 202°...
03/ Control Panel 1. Display To show the various menus and the selected function MENU To enter into move backward or leave the menu UP To go backward to move up in the menu 2. Buttons DOWN To go forward to move down in the menu ENTER To perform the desired functions 3.
04/ Fixture Installation DO install and operate by qualified operator. Fixture(s) should be installed in areas outside walking paths, seating areas, or away from areas were unauthorized personnel might reach the fixture by hand. NEVER stand directly below the fixture(s) when rigging, removing or servicing.
4.1 Hanging the Fixture There are four different installation methods for quick-lock fastener and clamp of this fixture, and it is recommended that you use the standard one. Standard installation (recommended): Non-standard installation 1: Non-standard installation 2: - 10 -...
Page 13
Splicing steps for the fixtures: Press the reset button and the lock catch will pop up automatically. Lift the bolt up and rotate it for a certain angle (10°-170°), then release your hand. Align and splice the second fixture to the first one, and splice the remaining fixtures in sequence.
Page 14
Align the upper positioning point with the lower one, then let go after rotating the bolt for a certain angle, and the bolt will be automatically inserted into the positioning point to lock the two fixtures. Note: When separating the fixtures, first lift the bolt upward and rotate it for a certain angle (10°-170°), then release your hand.
05/ How To Set The Unit 5.1 Main Functions To access the control menus, press the [MENU] button. Navigate the menu structure, using the [ENTER], [ UP] and [ DOWN] buttons. To select a menu option or to confirm a selection, press the [ENTER] button. ...
Page 16
MENU SUBMENU OPTIONS Default 1 IP Address Default 2 Network Manual Subnet Mask XXX.XXX.XXX.XXX 0-127 (Default=0) Sub-Net 0-15 (Default=0) Art-Net Settings Universe A 0-15 (Default=0) Universe B 0-15 (Default=0) sACN Universe 1-32000 (Default=1) sACN Settings sACN Priority 0-200 (Default=100) Artnet to DMX Tilt Invert Tilt Feedback Linear...
Page 17
MENU SUBMENU OPTIONS 1500Hz 2500Hz 4000Hz 5000Hz 6000Hz 10000Hz 15000Hz 20000Hz 25000Hz Invert Pixel Order Standard Power Mode Quiet CCT Calibration Display Invert Backlight Intensity 1-10 (Default=10) Display Settings °C Temperature Unit °F English Language Chinese Auto Test Mode 1 Mode 2 Clear No/Yes...
Page 18
MENU SUBMENU OPTIONS RGBW Red 10 0-255 0-255 Color RGBW Green 10 0-255 0-255 Macro RGBW Blue 10 0-255 0-255 Macro Sp Pixel White 10 0-255 0-255 Pixel Pixel 0-255 0-255 CW 1 Pixel Line W 0-255 0-255 WW 1 Line W ……...
Page 19
MENU SUBMENU OPTIONS Fixture Use Hour Total LED Hour LED Use Hour LED On Hour LED Hours Reset Password=050 Current LED 1 Temperature LED 2 LED 3 Base Fan Head Fan 1 Fixture Information Head Fan 2 Fan State Head Fan 3 Head Fan 4 Head Fan 5 Upgrade File...
Page 20
DMX Settings Enter the control menu and select DMX Settings, press ENTER. Use the UP/DOWN button to select Port A Address, Port B Address, DMX Channel Mode, No DMX Status, View DMX Value, Connect Option, Network, Art-Net Settings, sACN Settings or Artnet to DMX. Port A Address Select Port A Address, press ENTER.
Page 21
DMX Channel Mode Select DMX Channel Mode, press ENTER. Use UP/DOWN button to select between 17 CH, 27 CH, 99 CH, 108 CH, 168 CH, 8+100 CH, 8+160 CH and 21 CH, confirm your selection with ENTER. To exit the menu, press MENU, or wait 30 seconds. No DMX Status Select No DMX Status, press ENTER.
Page 22
Network Select Network, press ENTER. Use UP/DOWN button to select IP Address or Subnet Mask, confirm your selection with ENTER. To exit the menu, press MENU, or wait 30 seconds. Art-Net Settings Select Art-Net Settings, press ENTER. Use UP/DOWN button to select Net, Sub-Net, Universe A or Universe B, confirm your selection with ENTER.
Page 23
Fixture Settings Enter the control menu and select Fixture Settings, press ENTER. Use the UP/DOWN button to select Tilt Invert, Tilt Feedback, Dimmer Curve, Dimmer Speed, White Balance, LED Refresh Rate, Invert Pixel Order, Power Mode or CCT Calibration. Tilt Invert Select Tilt Invert, press ENTER.
Page 24
White Balance Select White Balance, press ENTER. Use UP/DOWN button to select Red, Green, Blue, Red1, Green1, Blue1…… or Red12, Green12, Blue12, confirm your selection with ENTER. Use UP/DOWN button to select a value between 125 and 255, confirm your selection with ENTER. To exit the menu, press MENU, or wait 30 seconds.
Page 25
Display Settings Enter the control menu and select Display Settings, press ENTER. Use the UP/DOWN button to select Display Invert, Backlight Intensity, Temperature Unit or Language. Display Invert Select Display Invert, press ENTER. Use UP/DOWN button to select No (display normal) or Yes (display inverted), confirm your selection with ENTER.
Page 26
Fixture Test Enter the control menu and select Fixture Test, press ENTER. Use the UP/DOWN button to select Auto Test or Manual Test. Auto Test Select Auto Test, press ENTER. The device immediately performs an automatic self-test. To end the automatic self-test and exit the menu, press MENU, or wait 30 seconds.
Page 27
LED Use Hour Select LED Use Hour, press ENTER. Use UP/DOWN button to select Total LED Hour (total time) or LED On Hour (current switch-on time), confirm your selection with ENTER. The total time or current switch-on time is displayed. Use UP/DOWN button to select LED Hours Reset, confirm your selection with ENTER.
Page 28
Error Logs Select Error Logs, press ENTER. Use UP/DOWN button to select Fixture Errors, confirm your selection with ENTER. The error list is displayed. Use UP/DOWN button to select Reset Error Log, confirm your selection with ENTER. If you wish to reset the relevant error logs, select Yes. If you do not wish to reset anything, select No.
Page 29
All Reset Select All Reset, press ENTER. Use UP/DOWN button to select No or Yes (the device will run built-in program to reset all to their home positions), confirm your selection with ENTER. To exit the menu, press MENU, or wait 30 seconds. Special Function Enter the control menu and select Special Function, press ENTER.
Page 30
RDM functions: Certain menus of the device and functions can be called up via the RDM protocol. The parameter IDs are implemented as follows for different commands: Command Command Command Parameter ID ‘Discovery’ ‘Set’ ‘Get’ DISC_UNIQUE_BRANCH √ √ √ DISC_MUTE √...
5.2 Home Position Adjustment To access the control menus, press the [MENU] button. To access the offset menus, long-press the [ENTER] button. Navigate the offset menus, using the [ENTER], [ UP] and [ DOWN] buttons. To select a menu option or to confirm a selection, press the [ENTER] button. ...
Page 32
Pixel Red 24 0~500 Pixel Green 24 0~500 Pixel Blue 24 0~500 Pixel CW 1 0~500 Pixel WW 1 0~500 …… …… Pixel CW 24 0~500 Pixel WW 24 0~500 Red 11 0~500 Green 11 0~500 Blue 11 0~500 White 11 0~500 Red 12 0~500...
Page 33
Frequency Select Frequency, press ENTER. Use UP/DOWN button to select a value, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Frequency VALUES 900Hz 772~1027 1000Hz 872~1127 1100Hz 972~1227 1200Hz 1072~1327 1300Hz 1172~1427 1400Hz 1272~1527 1500Hz...
Page 34
Select Red, press ENTER. Use UP/DOWN button to select a value between 0 and 1500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Green Select Green, press ENTER. Use UP/DOWN button to select a value between 0 and 1500, confirm your selection with ENTER.
Page 35
Pixel Green Select Pixel Green, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Pixel Blue Select Pixel Blue, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
Page 36
Green 1 Select Green 1, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Blue 1 Select Blue 1, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
Page 37
Blue 10 Select Blue 10, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. White 10 Select White 10, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
Page 38
Pixel Red 24 Select Pixel Red 24, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Pixel Green 24 Select Pixel Green 24, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
Page 39
Pixel CW 24 Select Pixel CW 24, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Pixel WW 24 Select Pixel WW 24, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
Page 40
White 11 Select White 11, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER. To exit the offset menu, press MENU, or wait 30 seconds. Red 12 Select Red 12, press ENTER. Use UP/DOWN button to select a value between 0 and 500, confirm your selection with ENTER.
06/ Control By Universal DMX Controller 6.1 DMX512 Connection 1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit.
6.2 Address Setting If you use a universal DMX controller to control the units, you have to set DMX address between 1 and 512 so that the units can receive DMX signal. Press the MENU button to access the control menus, select DMX Settings, press the ENTER button to confirm.
6.3 DMX512 Configuration Please control the fixture by referring to the configurations below. Attentions: The unit will maintain the last condition until reset if you cut-off the DMX signal. For the channel Function, keep the value for about 3 seconds, then the ...
Page 44
016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open SPECIAL FUNCTION 000-029 Null 030-039...
Page 45
MAIN GREEN 0%100% 000-255 MAIN BLUE 000-255 0%100% MAIN WHITE 000-255 0%100% LINE_W CW 0%100% 000-255 LINE_W WW 000-255 0%100% LINE_RGB RED 000-255 0%100% LINE_RGB GREEN 000-255 0%100% LINE_RGB BLUE 000-255 0%100% 27 Channels (Mode 2): CHANNEL VALUE FUNCTION TILT 000-255 0°202°...
Page 46
182-189 Open 190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open LINE_RGB STROBE 000-007 Close 008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231...
Page 47
170-179 CCT Calibration: Off 180-199 Null 200-209 All Reset 210-219 Dimmer Speed: Fast 220-229 Dimmer Speed: Smooth 230-255 Null MAIN RED 000-255 0%100% MAIN GREEN 000-255 0%100% MAIN BLUE 000-255 0%100% MAIN WHITE 000-255 0%100% MAIN CCT Null 001-004 8000K 005-009 7900K 010-013...
Page 52
248-255 Null LINE_W MACRO SPEED 000-127 Slow to Fast without Fade 128-255 Slow to Fast with Fade LINE_RGB RED 000-255 0%100% LINE_RGB GREEN 000-255 0%100% LINE_RGB BLUE 000-255 0%100% LINE_RGB COLOR 000-007 Null 008-015 Color1 016-023 Color2 024-031 Color3 032-039 Color4 040-047 Color5...
Page 54
008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open LINE_W STROBE 000-007...
Page 55
1300Hz 1400Hz 1500Hz 2500Hz 4000Hz 5000Hz 6000Hz 10KHz 15KHz 20KHz 25KHz 138-139 Null 140-149 Tilt Reset 150-159 Effect Reset 160-169 CCT Calibration: On 170-179 CCT Calibration: Off 180-199 Null 200-209 All Reset 210-219 Dimmer Speed: Fast 220-229 Dimmer Speed: Smooth 230-255 Null MAIN RED 1...
Page 56
MAIN RED 4 0%100% 000-255 MAIN GREEN 4 000-255 0%100% MAIN BLUE 4 000-255 0%100% MAIN WHITE 4 0%100% 000-255 MAIN RED 5 000-255 0%100% MAIN GREEN 5 000-255 0%100% MAIN BLUE 5 000-255 0%100% MAIN WHITE 5 000-255 0%100% MAIN RED 6 000-255 0%100%...
Page 57
MAIN BLUE 9 0%100% 000-255 MAIN WHITE 9 000-255 0%100% MAIN RED 10 000-255 0%100% MAIN GREEN 10 0%100% 000-255 MAIN BLUE 10 000-255 0%100% MAIN WHITE 10 000-255 0%100% LINE_W CW 1 000-255 0%100% LINE_W WW 1 000-255 0%100% LINE_W CW 2 000-255 0%100%...
Page 60
190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open LINE_W STROBE 000-007 Close 008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231...
Page 61
5000Hz 6000Hz 10KHz 15KHz 20KHz 25KHz 138-139 Null 140-149 Tilt Reset 150-159 Effect Reset 160-169 CCT Calibration: On 170-179 CCT Calibration: Off 180-199 Null 200-209 All Reset 210-219 Dimmer Speed: Fast 220-229 Dimmer Speed: Smooth 230-255 Null MAIN RED 1 000-255 0%100% MAIN GREEN 1...
Page 62
000-255 0%100% MAIN WHITE 4 000-255 0%100% MAIN RED 5 0%100% 000-255 MAIN GREEN 5 000-255 0%100% MAIN BLUE 5 000-255 0%100% MAIN WHITE 5 000-255 0%100% MAIN RED 6 000-255 0%100% MAIN GREEN 6 000-255 0%100% MAIN BLUE 6 000-255 0%100% MAIN WHITE 6...
Page 63
MAIN RED 10 0%100% 000-255 MAIN GREEN 10 000-255 0%100% MAIN BLUE 10 000-255 0%100% MAIN WHITE 10 0%100% 000-255 LINE_W CW 1 000-255 0%100% LINE_W WW 1 000-255 0%100% LINE_W CW 2 000-255 0%100% LINE_W WW 2 000-255 0%100% LINE_W CW 3 000-255 0%100%...
Page 65
LINE_RGB GREEN 6 0%100% 000-255 LINE_RGB BLUE 6 000-255 0%100% LINE_RGB RED 7 000-255 0%100% LINE_RGB GREEN 7 0%100% 000-255 LINE_RGB BLUE 7 000-255 0%100% LINE_RGB RED 8 000-255 0%100% LINE_RGB GREEN 8 000-255 0%100% LINE_RGB BLUE 8 000-255 0%100% LINE_RGB RED 9 000-255 0%100%...
Page 66
168 Channels (Mode 5): CHANNEL VALUE FUNCTION TILT 000-255 0°202° 000-255 TILT FINE ZOOM 000-255 WideNarrow DIMMER 0%100% 000-255 MAIN STROBE 000-007 Close 008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231...
Page 67
040-049 Dimmer Curve: Square Law 050-059 Dimmer Curve: Inv SQ Law 060-069 Dimmer Curve: S Curve 070-079 Power Mode: Standard 080-089 Null 090-099 Power Mode: Quiet 100-109 Led Frequency Setting Enable 110-119 Led Frequency Setting Disable 120-122 Null 900Hz 1000Hz 1100Hz 1200Hz 1300Hz...
Page 68
MAIN BLUE 2 0%100% 000-255 MAIN WHITE 2 000-255 0%100% MAIN RED 3 000-255 0%100% MAIN GREEN 3 0%100% 000-255 MAIN BLUE 3 000-255 0%100% MAIN WHITE 3 000-255 0%100% MAIN RED 4 000-255 0%100% MAIN GREEN 4 000-255 0%100% MAIN BLUE 4 000-255 0%100%...
Page 69
MAIN RED 8 0%100% 000-255 MAIN GREEN 8 000-255 0%100% MAIN BLUE 8 000-255 0%100% MAIN WHITE 8 0%100% 000-255 MAIN RED 9 000-255 0%100% MAIN GREEN 9 000-255 0%100% MAIN BLUE 9 000-255 0%100% MAIN WHITE 9 000-255 0%100% MAIN RED 10 000-255 0%100%...
Page 72
LINE_RGB RED 3 0%100% 000-255 LINE_RGB GREEN 3 000-255 0%100% LINE_RGB BLUE 3 000-255 0%100% LINE_RGB RED 4 0%100% 000-255 LINE_RGB GREEN 4 000-255 0%100% LINE_RGB BLUE 4 000-255 0%100% LINE_RGB RED 5 000-255 0%100% LINE_RGB GREEN 5 000-255 0%100% LINE_RGB BLUE 5 000-255 0%100%...
Page 73
LINE_RGB GREEN 10 0%100% 000-255 LINE_RGB BLUE 10 000-255 0%100% LINE_RGB RED 11 000-255 0%100% LINE_RGB GREEN 11 0%100% 000-255 LINE_RGB BLUE 11 000-255 0%100% LINE_RGB RED 12 000-255 0%100% LINE_RGB GREEN 12 000-255 0%100% LINE_RGB BLUE 12 000-255 0%100% LINE_RGB RED 13 000-255 0%100%...
Page 74
LINE_RGB BLUE 17 0%100% 000-255 LINE_RGB RED 18 000-255 0%100% LINE_RGB GREEN 18 000-255 0%100% LINE_RGB BLUE 18 0%100% 000-255 LINE_RGB RED 19 000-255 0%100% LINE_RGB GREEN 19 000-255 0%100% LINE_RGB BLUE 19 000-255 0%100% LINE_RGB RED 20 000-255 0%100% LINE_RGB GREEN 20 000-255 0%100%...
Page 75
8+100 Channels (Mode 6): CHANNEL VALUE FUNCTION Controlled by DMX TILT 0°202° 000-255 000-255 TILT FINE ZOOM WideNarrow 000-255 DIMMER 000-255 0%100% MAIN STROBE 000-007 Close 008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231...
Page 76
000-029 Null 030-039 Dimmer Curve: Linear 040-049 Dimmer Curve: Square Law 050-059 Dimmer Curve: Inv SQ Law 060-069 Dimmer Curve: S Curve 070-079 Power Mode: Standard 080-089 Null 090-099 Power Mode: Quiet 100-109 Led Frequency Setting Enable 110-119 Led Frequency Setting Disable 120-122 Null 900Hz...
Page 77
000-255 0%100% MAIN GREEN 2 000-255 0%100% MAIN BLUE 2 0%100% 000-255 MAIN WHITE 2 000-255 0%100% MAIN RED 3 000-255 0%100% MAIN GREEN 3 000-255 0%100% MAIN BLUE 3 000-255 0%100% MAIN WHITE 3 000-255 0%100% MAIN RED 4 000-255 0%100% MAIN GREEN 4...
Page 78
MAIN BLUE 7 0%100% 000-255 MAIN WHITE 7 000-255 0%100% MAIN RED 8 000-255 0%100% MAIN GREEN 8 0%100% 000-255 MAIN BLUE 8 000-255 0%100% MAIN WHITE 8 000-255 0%100% MAIN RED 9 000-255 0%100% MAIN GREEN 9 000-255 0%100% MAIN BLUE 9 000-255 0%100%...
Page 80
LINE_RGB RED 3 0%100% 000-255 LINE_RGB GREEN 3 000-255 0%100% LINE_RGB BLUE 3 000-255 0%100% LINE_RGB RED 4 0%100% 000-255 LINE_RGB GREEN 4 000-255 0%100% LINE_RGB BLUE 4 000-255 0%100% LINE_RGB RED 5 000-255 0%100% LINE_RGB GREEN 5 000-255 0%100% LINE_RGB BLUE 5 000-255 0%100%...
Page 81
LINE_RGB GREEN 10 0%100% 000-255 LINE_RGB BLUE 10 000-255 0%100% LINE_RGB RED 11 000-255 0%100% LINE_RGB GREEN 11 0%100% 000-255 LINE_RGB BLUE 11 000-255 0%100% LINE_RGB RED 12 000-255 0%100% LINE_RGB GREEN 12 000-255 0%100% LINE_RGB BLUE 12 000-255 0%100% 8+160 Channels (Mode 7): CHANNEL VALUE...
Page 82
140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open LINE_RGB STROBE 000-007 Close 008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181...
Page 83
160-169 CCT Calibration: On 170-179 CCT Calibration: Off 180-199 Null 200-209 All Reset 210-219 Dimmer Speed: Fast 220-229 Dimmer Speed: Smooth 230-255 Null Controlled by Art-Net MAIN RED 1 000-255 0%100% MAIN GREEN 1 000-255 0%100% MAIN BLUE 1 000-255 0%100% MAIN WHITE 1 0%100%...
Page 84
MAIN BLUE 5 0%100% 000-255 MAIN WHITE 5 000-255 0%100% MAIN RED 6 000-255 0%100% MAIN GREEN 6 0%100% 000-255 MAIN BLUE 6 000-255 0%100% MAIN WHITE 6 000-255 0%100% MAIN RED 7 000-255 0%100% MAIN GREEN 7 000-255 0%100% MAIN BLUE 7 000-255 0%100%...
Page 87
LINE_W CW 23 0%100% 000-255 LINE_W WW 23 000-255 0%100% LINE_W CW 24 000-255 0%100% LINE_W WW 24 0%100% 000-255 LINE_RGB RED 1 000-255 0%100% LINE_RGB GREEN 1 000-255 0%100% LINE_RGB BLUE 1 000-255 0%100% LINE_RGB RED 2 000-255 0%100% LINE_RGB GREEN 2 000-255 0%100%...
Page 88
LINE_RGB RED 7 0%100% 000-255 LINE_RGB GREEN 7 000-255 0%100% LINE_RGB BLUE 7 000-255 0%100% LINE_RGB RED 8 0%100% 000-255 LINE_RGB GREEN 8 000-255 0%100% LINE_RGB BLUE 8 000-255 0%100% LINE_RGB RED 9 000-255 0%100% LINE_RGB GREEN 9 000-255 0%100% LINE_RGB BLUE 9 000-255 0%100%...
Page 89
LINE_RGB GREEN 14 0%100% 000-255 LINE_RGB BLUE 14 000-255 0%100% LINE_RGB RED 15 000-255 0%100% LINE_RGB GREEN 15 0%100% 000-255 LINE_RGB BLUE 15 000-255 0%100% LINE_RGB RED 16 000-255 0%100% LINE_RGB GREEN 16 000-255 0%100% LINE_RGB BLUE 16 000-255 0%100% LINE_RGB RED 17 000-255 0%100%...
Page 90
LINE_RGB BLUE 21 0%100% 000-255 LINE_RGB RED 22 000-255 0%100% LINE_RGB GREEN 22 000-255 0%100% LINE_RGB BLUE 22 0%100% 000-255 LINE_RGB RED 23 000-255 0%100% LINE_RGB GREEN 23 000-255 0%100% LINE_RGB BLUE 23 000-255 0%100% LINE_RGB RED 24 000-255 0%100% LINE_RGB GREEN 24 000-255 0%100%...
Page 91
008-015 Open 016-131 Strobe from Slow to Fast 132-139 Open 140-181 Slow Open Fast Close from Slow to Fast 182-189 Open 190-231 Fast Open Slow Close from Slow to Fast 232-239 Open 240-247 Random Strobe from Slow to Fast 248-255 Open LINE_RGB STROBE 000-007...
Page 92
138-139 Null 140-149 Tilt Reset 150-159 Effect Reset 160-169 CCT Calibration: On 170-179 CCT Calibration: Off 180-199 Null 200-209 All Reset 210-219 Dimmer Speed: Fast 220-229 Dimmer Speed: Smooth 230-255 Null MAIN RED 000-255 0%100% MAIN GREEN 000-255 0%100% MAIN BLUE 000-255 0%100% MAIN WHITE...
07/ Error Information Error codes are shown continuously in the display when the fixture fails and they will not disappear until the fixture is repaired. CPU-B/C/D/E/F Error Check whether the 485 (DATA) leads on the PCB board are installed in place or disconnected.
Page 94
Tilt Encode Disable Check whether the encoder on the tilt is damaged. Network Error Check whether the network module is installed. Check whether the network module is damaged. Zoom Error Check whether the position of the zoom where the magnet is installed falls off or is damaged.
Page 95
BaseFan Start Err Check whether the fan is not running. Check whether the fan leads are installed in place or disconnected. Check whether the fan is damaged. Check whether there are obstacles in the fan operating range. HeadFan1/2/3/4/5 Start Err Check whether the fan is not running.
08/ Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for troubleshooting: A. The unit does not work, no light and the fan does not work Check the connected power and main fuse. ...
09/ Fixture Cleaning It is absolutely essential that the fixture is kept clean to ensure the maximum light-output and allow the fixture to function reliably throughout its life. The fixture must be cleaned regularly to avoid dust, dirt and smoke-fluid residues building up on or within the fixture. The cleaning frequency depends on the application environment.
Page 99
Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 2014/30/EU. EN 55032: 2015+A1: 2020; EN 55035: 2017+A11: 2020; EN IEC 61000-3-2: 2019+A1: 2021; EN 61000-3-3: 2013+A1: 2019+A2: 2021.