1. Manuals
  2. Brands
  3. ACME Manuals
  4. DJ Equipment
  5. LED WAVE 100
  6. User manual

ACME LED WAVE 100 User Manual

Hide thumbs Also See for LED WAVE 100:
Table of Contents

Advertisement

Quick Links

LED-WAV-100W

User Manual

Please read the instruction carefully before use

Advertisement

Table of Contents
loading

Related Manuals for ACME LED WAVE 100

Summary of Contents for ACME LED WAVE 100

  • Page 1: User Manual

    LED-WAV-100W User Manual Please read the instruction carefully before use...

  • Page 2: Table Of Contents

    CONTENTS 1. Safety Instruction ................... 2 2. Technical Specification ................3 3. How To Set The Unit ................4 3.1 Control Panel ................... 4 3.2 Lens Installation ................5 3.3 Main Function .................. 6 4. How To Control The Unit ..............10 4.1 Master/Slave Built In Preprogrammed Function ......

  • Page 3: Safety Instruction

    1. Safety Instruction Please read this instruction carefully which includes important information about the installation, usage and maintenance. WARNING Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ...

  • Page 4: Technical Specification

    Warning:  To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.  The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Caution: There are no user serviceable parts inside the unit.

  • Page 5: How To Set The Unit

    ◇ High efficiency and low power consumption ◇ Input Voltage: AC 100V~240V, 50/60Hz ◇ Power Consumption: 105W ◇ Light Source: 1 x 100W cold white LED ◇ Weight: 6.2Kgs ◇ Dimension: 309 x 271 x 210 mm 3. How To Set The Unit 3.1 Control Panel 1.

  • Page 6: Lens Installation

    DMX512 link, use 3-pin XLR cable to link the next unit and output DMX signal. 4. Fuse (T 3.15A): Protects the unit from over-voltage or short circuit. 5. MAINS IN: Connection from main power supply; 6. MAINS OUT: Connection for main power supply to the next unit. 7.

  • Page 7: Main Function

    C. Replace the lens You could replace the other lens if you want to, as following picture. You should screw the lens roller to take it down as NO.1, and bring the lens out as No.2. Then you could replace the lens that you want to. Notes: the lens roller has two slots for the lens;...
  • Page 8 DMX 512 Address Setting Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address has been selected, press ENTER button to setup or automatically exit menu mode without any change after one minute.
  • Page 9 Show Mode Press the MENU button up to when the is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (Random show), (show 1) or (show 2). Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after one minute.
  • Page 10 Press the MENU button up to when the is shown on the display. Pressing ENTER button, and use DOWN and UP button to select (0-255) or (000-2555,clockwise/counterclockwise) , or (000-255),press ENTER button to confirm and use DOWN and UP button to adjust the value, once select press ENTER button to setup or automatically exit menu mode without any change after one minute.

  • Page 11: How To Control The Unit

    setup. Back to the functions without any change press MENU button. 4. How To Control The Unit You can operate the unit in three ways: 1. By master/slave built-in preprogram function 2. By easy controller 3. By DMX controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be effected at once.

  • Page 12: Dmx Controller

    3. Slow Sync. Strobe LED OFF Mode LED blinking 4.3 DMX Controller Use universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Press the MENU button up to when the is showing on the display.

  • Page 13: Dmx512 Connection

    066 ~ 076 Color 3 077~ 087 Color 3  Color 4 088 ~ 098 Color 4 099 ~ 109 Color 4  Color 5 110 ~ 120 Color 5 121 ~ 127 Color 5  Open Continuous Rotation 128~ 187 CW Rotation: fast ...

  • Page 14: Troubleshooting

    input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. 4.

  • Page 15: Fixture Cleaning

    C. Some units don’t respond to the easy controller 1. You may have a break in the DMX cabling. Check the LED for the response of the master/ slave mode signal. 2. Wrong DMX address in the unit. Set the proper address. D.
  • Page 16 Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 2004/108/EC. EN55103-1: 2009 ; EN55103-2: 2009; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008. &...

This manual is also suitable for:

Led-wav-100w

Table of Contents