Table of Contents
Advertisement
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
4. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
5. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin4/5: Not used.
8. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture's optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
Innovation, Quality, Performance
15E
COLOR FUSION
CF-805
User Manual
Please read the instructions carefully before use
Advertisement
Table of Contents
Related Manuals for ACME Color Fusion CF-805
Summary of Contents for ACME Color Fusion CF-805
-
Page 1: User Manual
3-pin XLR-plug and plug it in the DMX-output of the last fixture. 4. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). 5. - Page 2 Blackout To blackout all the fixture Function Strobe Select 9 Colors Show modes Setting speed TABLE OF CONTENTS 1.Synchronous 1. White 1. Show 1 1. Slow speed strobe in white 2. Red 2. Show 2 2. Middle speed 2. Synchronous 3.
- Page 3 1. Safety Introductions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING Please keep the User Manual for future consultation. Please be sure receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the fixture. Please ensure the voltage and frequency of power supply match the power requirements of the fixture.
- Page 4 2. Technical Specifications ¥ Power supply 100V-240V~50/60Hz ¥ Power consumption：36 W ¥ LED Red 128pcs, Green 128pcs, Blue 128pcs ¥ Channels 4, 6, 9, 15, 27, 24 channel mode ¥ Dimension：965 x 64 x 153 mm ¥ Weight：2.8 kg 3. Installation The fixture is able to hanging on the truss to increase the pleasured ambience.
- Page 5 6. How to control the fixture There are three ways to set-up the DMX address: A. Universal DMX controller B. Master/Slave operation C. Easy controller (by CA-8) A. Universal DMX controller 3.1 Fuse Replacement The user need to set the lighting channel mode first while control by universal DMX The fuse of Color Fusion may be replaced as below.
- Page 6 Button C. By Universal DMX controller MENU To select the programming functions The fixtures can be remote setting DMX address by universal DMX controller. First, programming two scenes into one chase and then link the fixtures to the universal DMX DOWN To go backward in the selected functions controller.
- Page 7 (Display Inversion mode) or (Display normal mode), To go back to the functions press the MENU button. 5. DMX512 Address Setting A. By LED Display Panel 1. Each fixture needs to have an address setting to receive the data sent from the controller. The address number is between 0-511 (usually 0 &...
- Page 8 DMX 512 Address Setting Blackout Mode Press the MENU button until the is shown on the display. Pressing ENTER button Press the MENU button until the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (yes blackout) or and the display will blink.