Table of Contents
Advertisement
1. Safety
•
F80-Q7, F80-4K7 :
-
The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014.
60825–1:2007, and with performance standards for laser products under 21 CFR 1040, except with respect to those
characteristics authorized by Variance Number 2017-V-4837 effective September 13, 2017 Do not stare into Beam.
-
This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk Group 3 (RG3) when an
interchangeable lens with throw ratio greater than 3.5 is installed. For Northern America, installation requirements according
to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.0 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are intended for professional
use only, and are not intended for consumer use. Safety considerations for RG3 projectors are discussed in section "Risk
Group 3 Safety", page 8 .
-
This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very dangerous and should
never be attempted.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training
and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH
VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of mea-
sures to minimize the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable
of such risks, are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to
any person other than SERVICE PERSONNEL. When installing an interchangeable lens with a throw ratio that make the projector
become RG3, refer to chapter "Risk Group 3 Safety", page 8 . Such combination of projector and lens are intended for professional
use only, and are not intended for consumer use.
FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED PERSONNEL familiar with
potential hazards associated with high intensity light beams.
1.2
Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables
are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type plug. Never use 2-prong power cords, as this is dangerous
and could lead to electrical shock.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
•
the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by qualified service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
•
Make sure that no objects enter into the vents and openings of the set.
•
Do not expose this projector to rain or moisture.
•
The projector is designed for indoor use only. Never operate the unit outdoors.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
•
Do not disassemble this projector, always take it to qualified service personnel when service or repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
4
The projector conforms with IEC
R5906852 F80 SERIES 21/09/2017
Advertisement
Table of Contents
