Related Manuals for Raisecom OPCOM3100 series
Summary of Contents for Raisecom OPCOM3100 series
- Page 1 OPCOM3100 CONFIGURATION GUIDE SOFTWARE VERSION：2.1.5 Raisecom technology Co., Ltd （11/2005）...
-
Page 2: Table Of Contents
Contents Overview ........................3 Audience......................3 Organization ....................... 3 Definitions ......................3 References ......................3 Introduction ........................ 4 How to use command-line ..................5 Requirements of software and hardware ............5 Getting help ......................5 Use history commands ..................5 Editing properties.................... - Page 3 Raisecom Technology Co., Ltd 10.1 Configuration commands .................. 28 10.2 Examples ......................28 11 Configuration applications..................30 11.1 Point-to-point 1+1 protection configuration ............30 11.2 Chain topology none-protection configuration........... 31 11.3 Example of 2F SNC-P configuration ..............33 12 Appendix: Abbreviation .................... 38...
-
Page 4: Overview
Raisecom Technology Co., Ltd 1 Overview 1.1 Audience This guide is for experienced network administrators who are responsible for configuring and maintaining OPCOM3100. And it describes the device function as well as how to configure. 1.2 Organization There are mainly 10 chapters in this guide:... -
Page 5: Introduction
Raisecom Technology Co., Ltd 2 Introduction OPCOM3100 is an SDH access device which supports both Ethernet services and E1 services, and is developed as an edge access device for the purpose of full use of the resource of SDH networks. OPCOM3100 can aggregate the user data flows and multiplex them to STM-1 data. -
Page 6: How To Use Command-Line
Raisecom Technology Co., Ltd 3 How to use command-line 3.1 Requirements of software and hardware Operation environment of hardware: platform of OPCOM3100 Computer serial interface; Operation environment of software: WIN98/WIN2000/WINDOWS XP 3.2 Getting help command Function description help Getting a brief description from help system... - Page 7 Raisecom Technology Co., Ltd Ctrl+a: move the cursor to the beginning of the command line Ctrl+e: move the cursor to the end of the command line Ctrl+k: delete all the characters on the right side the cursor Ctrl+w: delete all the characters on the left side of the cursor...
-
Page 8: Configuring System Commands
Raisecom Technology Co., Ltd 4 Configuring system commands Basic system configuration and user management. 4.1 Basic system commands and configuration chinese show help information of the command in Chinese english show help information of the command in English clear clear the information on the screen... -
Page 9: Upgrade The Program File From Bootrom
A: The user who has management privilege can login and enter the privileged EXEC by the serial port; B: Enter reboot command; C: Press the space key to enter the [raisecom] interface, enter? to show the command list. show this list... - Page 10 Raisecom Technology Co., Ltd through the serial port, now press the [Transfer] option in the serial port as follows: Choose the file to transmit: Press [Browse] option to choose the program file to be downloaded, press [Send] then there will be the following interface:...
- Page 11 A: The user who owns the management privilege can login and enter the privileges EXEC mode by the serial port; B: Enter reboot command; C: Press the space key to enter the [raisecom] interface, enter ? to show the command list. show this list...
-
Page 12: User Management
Now the program upgrade has been finished. 4.3 User management The system has a default username raisecom and the password raisecom; Add a new user, the steps are as follows: steps Command... - Page 13 Raisecom Technology Co., Ltd PASSWORD password information; user USERNAME privilege USERNAME user name; [ADMINISTRANT | NORMAL | Privilege key word for privilege LIMITED] [ADMINISTRANT | NORMAL | LIMITED] user privilege write Save the configuration information show user Show the user information...
-
Page 14: Configuring Network Protocols
Raisecom Technology Co., Ltd 5 Configuring network protocols This chapter includes the following sections: Configure the mapping from IP address to physical address Configure IP address of SNMP interface Configure a static routing Configure COMMUNITY table of SNMP Configure SNMP trap server host 5.1 Configure the mapping from IP address to physical... -
Page 15: Configure Ip Routing
Raisecom Technology Co., Ltd case ip address is available. Command Description config Enter global configuration mode interface snmp Enter SNMP interface configuration mode Ａ ip address A.B.C.D { .B.C.D} Configure IP address of network management A.B.C.D address network management in decimal with dot. -
Page 16: Configure Snmp Community Table
Show COMMUNITY table Using no snmp-server community COMMUNITYNAME to delete one COMMUNITY in global configuration mode For example: add a COMMUNITY named raisecom that can be both read and written OPCOM3100# config Configuration mode, one command input per time. End with CTRL... -
Page 17: Configure Snmp Trap Server Host
Raisecom Technology Co., Ltd 5.5 Configure SNMP trap server host The trap server host is in charge of receiving TRAP, the default interface is 162 Command Description config Enter global configuration mode snmp-server host A.B.C.D Configuring a SNMP trap server host {<1-65535>}... -
Page 18: Configure Ethernet Interfaces
Raisecom Technology Co., Ltd 6 Configure Ethernet interfaces This chapter includes: Configure timeslots of Ethernet interfaces Command Description config Enter global configuration mode interface eth <1-8> Enter Ethernet interface configuration mode <1-8> serial number of the interface timeslot add sdh <1-2> vc12... -
Page 19: Configure E1 Interfaces
Raisecom Technology Co., Ltd 7 Configure E1 interfaces This chapter includes: Configure timeslots of E1 interfaces Command Description config Enter global configuration mode interface e1 <1-32> Enter E1 interface configuration mode <1-32> range of serial number of E1 interfaces, if there is E1 sub card the range is 1-32 and otherwise the range is 1-16 timeslot add sdh <1-2>... -
Page 20: Configure Cross Connect
Raisecom Technology Co., Ltd 8 Configure cross connect This chapter includes: configure SDH cross connect from one timeslot to the same or from one timeslot to another. Command Description Enter global configuration mode config Configure a crossconnect from timeslot 1 of... -
Page 21: Networking
Raisecom Technology Co., Ltd 9 Networking OPCOM3100 is available for low order cross connect of VC-12. With bi-directional optical interfaces and tributary interfaces of Ethernet and E1, OPCOM3100 can be configured conveniently to satisfy all the topologies of user access... -
Page 22: Ring Topology
Raisecom Technology Co., Ltd Chain topology TM and ADM can configure none-protection chain topology network, and double TMs and ADM can configure the linear low order VC protection of STM-1 level. When configured as 1+1 protection mode, service reliability will enhance but access ability will reduce;... -
Page 23: Configuration Command
Raisecom Technology Co., Ltd transmitting the data bi-directionally, and every receiving note receives the data bi-directionally. So the total service flow is lower than the device capacity. 2F SNC-P is suitable for access network, relay network and long distance network., which are concentrated, low service flow. -
Page 24: Chain Topology
Raisecom Technology Co., Ltd Set successfully OPCOM3100(config-snmp)# exit OPCOM3100(config)# interface dcc 1 OPCOM3100(config-dcc/1)# ip address 192.168.2.66 Set successfully OPCOM3100(config-dcc/1)# exit OPCOM3100(config)# interface dcc 2 OPCOM3100(config-dcc/2)# ip address 192.168.3.66 Set successfully OPCOM3100(config-dcc/2)# work mode client Set successfully OPCOM3100(config-dcc/2)# auto-connect Set successfully OPCOM3100(config-dcc/2)# ：... - Page 25 Raisecom Technology Co., Ltd Chain topology Configuration commands: OPCOM3100A： OPCOM3100(config)# interface snmp OPCOM3100(config-snmp)# ip address OPCOM3100(config-snmp)# ip address 192.168.2.66 Set successfully OPCOM3100(config-snmp)# exit OPCOM3100(config)# interface dcc 1 OPCOM3100(config-dcc/1)# ip unnumbered Set successfully OPCOM3100(config-dcc/1)# OPCOM3100B： OPCOM3100(config)# interface snmp OPCOM3100(config-snmp)# ip address OPCOM3100(config-snmp)# ip address 192.168.3.66...
-
Page 26: Ring Topology
Raisecom Technology Co., Ltd OPCOM3100(config-dcc/2)# OPCOM3100B： OPCOM3100(config)# interface snmp OPCOM3100(config-snmp)# ip address OPCOM3100(config-snmp)# ip address 192.168.4.66 Set successfully OPCOM3100(config-snmp)# exit OPCOM3100(config)# interface dcc 2 OPCOM3100(config-dcc/2)# ip unnumbered Set successfully OPCOM3100(config-dcc/2)# work mode client Set successfully OPCOM3100(config-dcc/2)# auto-connect Set successfully OPCOM3100(config-dcc/2)# 9.5.3 Ring topology... - Page 27 Raisecom Technology Co., Ltd Set successfully OPCOM3100(config-dcc/1)# exit OPCOM3100(config)# interface dcc 2 OPCOM3100(config-dcc/2)# ip unnumbered Set successfully OPCOM3100(config-dcc/2)# work mode client Set successfully OPCOM3100(config-dcc/2)# auto-connect Set successfully OPCOM3100(config-dcc/2)# OPCOM3100B： OPCOM3100(config)# interface snmp OPCOM3100(config-snmp)# ip address OPCOM3100(config-snmp)# ip address 192.168.2.66 Set successfully...
- Page 28 Raisecom Technology Co., Ltd OPCOM3100(config-dcc/2)# auto-connect Set successfully OPCOM3100(config-dcc/2)# OPCOM3100D： OPCOM3100(config)# interface snmp OPCOM3100(config-snmp)# ip address OPCOM3100(config-snmp)# ip address 192.168.4.66 Set successfully OPCOM3100(config-snmp)# exit OPCOM3100(config)# interface dcc 1 OPCOM3100(config-dcc/1)# ip unnumbered Set successfully OPCOM3100(config-dcc/1)# exit OPCOM3100(config)# interface dcc 2 OPCOM3100(config-dcc/2)# ip unnumbered...
-
Page 29: Network Topology Of Incontinuous Dcc
Raisecom Technology Co., Ltd 10 Network topology of incontinuous DCC Network topology: If the network is not only organized by OPCOM3100, DCC channel is not continuous when there are other types of device or network, in this case we use data network to manage and control remote OPCOM3100. - Page 30 Raisecom Technology Co., Ltd OPCOM3100(config)# snmp-server host 192.168.4.250 Set successfully...
-
Page 31: Configuration Applications
Raisecom Technology Co., Ltd 11 Configuration applications This chapter includes: point to point 1+1 protection configuration chain topology none-protection configuration ring topology 2F SNC-P configuration 11.1 Point-to-point 1+1 protection configuration Topology: OPCOM3100-A Port1 Port1 OPCOM3100-B Port2 Port2 Point to point networking Service requirement There are 2 E1 services of which the timeslot is 1 and 3;... -
Page 32: Chain Topology None-Protection Configuration
Raisecom Technology Co., Ltd device-type tm OPCOM3100(config)# sdh net-type Configure the network type of device line OPCOM3100(config)#exit OPCOM3100#write Save the configuration OPCOM3100#reboot Reset device OPCOM3100(config)#interface e1 Enter E1 interface 1 Configure timeslot 1 to E1 interface 1 OPCOM3100(config-e1/1)# Timeslot add sdh 1 vc12 1... - Page 33 Raisecom Technology Co., Ltd Total Timeslot table name timeslot port1 1-10 port2 1-10 port1 1-10 port1 1-10 E1 1-10 E1 1-10 E1 1-10 E1 17-26 STM-1 port1 11-21 port1 11-21 E1 11-21 E1 11-21 Configuration commands Configure TM1 Command Description...
-
Page 34: Example Of 2F Snc-P Configuration
Raisecom Technology Co., Ltd device-type tm OPCOM3100(config)# Configure the network topology of device net-type line OPCOM3100(config)#sdh Disable the protection protect-switch disable OPCOM3100(config)#exit OPCOM3100#write Save the configuration OPCOM3100#reboot Reset the device Configure E1 interfaces 1 to 10 the timeslots 1 OPCOM3100(config-e1/1)#... - Page 35 Raisecom Technology Co., Ltd Service requirements There are 10 2M Ethernet services from ADM A to ADM B, 5 2M and one 10M from A to C, 2 2M from B to D, and 5 2M from C to D.
- Page 36 Raisecom Technology Co., Ltd sdh crossconnect source-port timeslot destination-port 2 timeslot 22 OPCOM3100(config)# Configure crossconnect of the service from C to sdh crossconnect source-port D, timeslot 23-27 of optical interface 1 to timeslot timeslot 23-27 of optical interface 2. destination-port 2 timeslot 23 …...
- Page 37 Raisecom Technology Co., Ltd OPCOM3100(config)# sdh crossconnect source-port timeslot destination-port 2 timeslot 27 OPCOM3100(config)# Enter E1 interface configuration mode Interface E1 1 OPCOM3100(config-e1/1)# Configure E1 interfaces 1 to 10 the timeslots 1 Timeslot add sdh 1 vc12 1 to 10, correspond one to one.
- Page 38 Raisecom Technology Co., Ltd Configure Ethernet interface 1 the timeslots OPCOM3100(config-eth/1)# 16-20 Timeslot add sdh 1 vc12 16-20 Configure E1 interfaces 23 to 27 the timeslots OPCOM3100(config-e1/23)# 23 to 27, correspond one to one. Timeslot add sdh 1 vc12 23 ……...
-
Page 39: Appendix: Abbreviation
Raisecom Technology Co., Ltd 12 Appendix: Abbreviation Abbreviations English Add-Drop Multiplexer Alarm Indication Signal Automatic Protection Switching Administrative Unit AU-n Administration Unit，level n Administration Unit Group AU-PTR Administration Unit Pointer Background Block Error BBER Background Block Error Ratio Bit Error Ratio... - Page 40 Raisecom Technology Co., Ltd Local Craft Terminal Loss Of Frame Loss Of Pointer Loss Of Signal Lower order Path Connection Medium Access Control Metropolitan Area Network Micro Control Unit Mediation Device Mediation Function Medium Independent Interface Multi Mode Multiplex Section...
- Page 41 Raisecom Technology Co., Ltd Sequel Abbreviations English MS-AIS Multiplex Sections - Alarm Indication Signal MSOH Multiplex Section OverHead Multiplex Section Protection Network Element Network Element Function Network Element Layer Network Manager Layer Network Management System Operation, Administration and Maintenance Out of Frame Second...
- Page 42 Raisecom Technology Co., Ltd Sequel Abbreviations English RMII Reduced Medium Independent Interface Regenerator Section RSOH Regenerator Section OverHead Synchronous Digital Hierarchy SDH Equipment Clock Severely Error Second SESR Severely Error Second Ratio SETS Synchronous Equipment Timing Source Single Mode SNCP...
- Page 43 Raisecom Technology Co., Ltd @2005 Raisecom Technology Co., Ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification.