Related Manuals for Raisecom RCMS2401-30
Summary of Contents for Raisecom RCMS2401-30
- Page 1 RCMS2401-30 Modular Ethernet Multiplexer User Manual (Rev. A) Beijing Raisecom Science & Technology Co., Ltd...
-
Page 2: Table Of Contents
CONTENTS ..............................1 HAPTER VERVIEW 1.1 Main Features ..............................1 1.2 Part Number Explanation ........................... 1 ........................3 HAPTER ECHNICAL PECIFICATIONS 2.1 E1 Interface Specification ........................... 3 2.2 Fast Ethernet Interface Specification........................3 2.3 Optical Interface Specification..........................3 2.4 Ambience................................3 .......................... -
Page 3: Chapter 1 Overview
Fast Ethernet on to one fiber-optic cable, and implement the wire-speed transmission of the Ethernet data. RCMS2401-30 is featured by high integration and complete network management functions. It can be installed into the Raisecom 3U-high 16-slot chassis, or desktop single-slot chassis, providing various network management functions. - Page 4 Beijing Raisecom Science & Technology Co., Ltd Example RC MS 2 4 01 – 30 – S2 Single mode optical interface, 10-60 km 1 E1 channel 1 Ethernet interface Modular, single-strand fiber-optic L2 Ethernet switching capability Multi-service Raisecom code (RC short for Raisecom)
-
Page 5: Chapter 2 Technical Specifications
Beijing Raisecom Science & Technology Co., Ltd Chapter 2 Technical Specifications 2.1 E1 Interface Specification Bit rate: 2048Kbps±50ppm Line code: HDB3 Interface impedance: 120Ω balanced signal Electrical characteristic: Compliant to ITU-T G.703 Transfer characteristic: Compliant to ITU-T G.823 Jitter Tolerance: ITU-T G.724... -
Page 6: Chapter 3 Configuration Guide
3.1 Description of the Front Panel The sketch of the RCMS2401-30 front panel Optical Connector: The optical interface type of RCMS2401-30 is SC/PC. LAL (Local Alarm): The red alarm indicator will be lightened when error occurs at local optical receiving direction. -
Page 7: Dip-Switch Setup
Beijing Raisecom Science & Technology Co., Ltd 3.2 Dip-switch Setup 3.2.1 SW1 for Working Modes SW1 is an 8-bit dipswitch, as the figure on the right 1 2 3 4 5 6 7 8 Switch OFF (default status) Enable Ethernet interface auto-sensing... -
Page 8: E1 Remote Loop-Back Test
When the equipment is connected as the following topology, the remote network management can be implemented. A． The host-site module is installed in Raisecom’s dedicated 16-slot 3U-high chassis, which also has the network management module installed. The remote-site module is installed in Raisecom’s single slot chassis. -
Page 9: Chapter 4 Installation And Test
Place the equipment at stable and secure environment. Pay attention to the requirements of the ambience. 4.3 Installation This module can be installed into Raisecom’s dedicated 16-slot 3U-high chassis, 4-slot 1U-high chassis, and single slot chassis. Slowly insert the module into the slot to the end, and fasten the fixing screw tightly. -
Page 10: Function Configuration
Beijing Raisecom Science & Technology Co., Ltd Ethernet Interface Connect with Cat. 5 or hyper Cat. 5 twisted-pair cables. Either straight-through or crossover cable is OK. Optical Interface Plug the tail fiber into the fiber socket to the end. 4.3.2 Function Configuration After connecting the cables and applying the power supply, there shall not be alarms at the optical interface. -
Page 11: Appendixa Cable Making
Beijing Raisecom Science & Technology Co., Ltd Appendix A Cable Making A.1 E1 Cable Making Pin Number Definition OUT+ OUT- Not Used Not Used Not Used Not Used A.2 Ethernet Cable Making Use Cat.5 twisted-pair cable with RJ45 connector to connect this equipment. Note that the cable shall not be longer than 100 meters.