Related Manuals for Raisecom RCMS2101-30-FV35
Summary of Contents for Raisecom RCMS2101-30-FV35
- Page 1 RCMS2101-30-FV35 RCMS2301-30-FV35 RCMS2501-30-FV35 Standalone, Fiber Optic Ethernet Multiplexer User Manual Raisecom Technology Co., Ltd. (10/2005)
-
Page 2: Cautions
Raisecom Technology Co., Ltd 1. Cautions Please read the following notices carefully before installing and using the device, Raisecom does not respond to any loss that caused by violating safety notice. RCMS2X01-30-FV35 provides two types of power supply: AC and DC. When using DC power supply, please plug the power supply connectors according to this mannual strictly and avoid contrary connecting. -
Page 3: Table Of Contents
Raisecom Technology Co., Ltd Contents Cautions ............................1 Overview ............................3 2.1. Introduction ..........................3 2.2. Main Features ..........................3 2.3. Model Number Description......................3 2.4. Equipment Structure........................4 Parameters............................5 3.1. V.35 Interface Specification ......................5 3.2. Ethernet Interface Specification ....................5 3.3. Optical Interface Specification ....................5 3.4. -
Page 4: Overview
Standalone, dual-strand fiber Switch on layer 2 Multi-service device Company codename (Raisecom) : Standalone dual-strand fiber Ethernet multiplexer RCMS2101-30-FV35 shall work in pairs, or Note work with RCMS2201-30 modular multiplexer. Standalone RCMS2301-30-FV35 and RCMS2501-30-FV35 single strand fiber Ethernet multiplexer shall be deployed in pairs. -
Page 5: Equipment Structure
Raisecom Technology Co., Ltd 2.4. Equipment Structure Compact desktop design with dimension: 142mm (W) * 38mm * (H)* 178mm (D) -
Page 6: Parameters
Raisecom Technology Co., Ltd 3. Parameters 3.1. V.35 Interface Specification Physical characteristic: Compliant to V.35 interface specification Type of interface: ISO2593 female connector (34-pin female) Working mode: Bit rate: N*64Kbps (N=1~31) at framed E1 mode 2048Kbps at unframed E1 mode 3.2. -
Page 7: Power Supply
Raisecom Technology Co., Ltd V.35 BANWIDTH TS[0] TS[1] TS[16] TS[N+1] ¡ - ¡ - ¡ - ¡ - ¡ - ¡ - TS[31] 3.5. Power Supply Power supply voltage: DC -48V, tolerance range -36V ~ -72V AC 220V, tolerance range 165V ~ 265V Power consumption: ≤... -
Page 8: How To Use
Ethernet interface is 10/100Mbps auto sensing and can be configured. It is capable of auto MDI/MDIX and can be connected with either straight-through or crossover cable. 4.1.4. Optical Interface For dual-strand fiber model, RCMS2101-30-FV35, the TX wavelength is 1310nm and fiber... -
Page 9: Description Of The Rear Panel
Raisecom Technology Co., Ltd connector type is DSC/PC. TX stands for optical output, RX for optical input. For single strand fiber model, RCMS2301-30-FV35 and RCMS2501-30-FV35, the TX wavelength of RCMS2301-30-FV35 is 1310nm, and the TX wavelength of RCMS2501-30-FV35 is 1550nm. The fiber connector type is SC/PC. -
Page 10: Bottom Dip-Switch
Raisecom Technology Co., Ltd Terminal Timing (A) — SCTE(A) Terminal Timing (B) — SCTE(B) Request to Send — RTS Clear to Send — CTS Data Set Ready — DSR Data Carrier Detect — DCD Data Terminal Ready — DTR I—Input; O—Output 4.3. - Page 11 Raisecom Technology Co., Ltd 15×64K=960K 16×64K=1024K 17×64K=1088K 18×64K=1152K 19×64K=1216K 20×64K=1280K 21×64K=1344K 22×64K=1408K 23×64K=1472K 24×64K=1536K 25×64K=1600K 26×64K=1664K 27×64K=1728K 28×64K=1792K 29×64K=1856K 30×64K=1920K (Max bandwidth 31×64K=1984K (Max bandwidth In the above table, ‘1’ stands for OFF status of the switch, and ‘0’ stands for ON status. For example, the binary code corresponding to 384kbps bandwidth is ‘00110’.
-
Page 12: The Setup For Sw2: Factory Default Setting All Off
Raisecom Technology Co., Ltd The 7 and 8 bits: clock mode option Timing Resource Option Master Clock (Internal) V.35 Terminal Clock Vacant Slave Clock (follow the link clock) Users are advised to select the most suitable timing resource. When configuring clock modes, V.35 DTE interface on Routers shall also be configured. -
Page 13: The Setup For Sw3: Factory Default Setting All Off
Raisecom Technology Co., Ltd 4.3.3. The setup for SW3: factory default setting all OFF The 1 bit: Ethernet auto-negotiation capability enable/disable When this bit is switched to off, auto-negotiation capability is enabled. When this bit is switched to on, auto-negotiation capability is disabled. The working data rate and... - Page 14 Raisecom Technology Co., Ltd of SW3 is switched to ON. If the optical fiber is connected properly, the loop-back status can be viewed at the port of local Router. The 8 bit: Local loop-back function Local Loop-back is performed at local V.35 interface and used for test and diagnosis the V.35 interface.
-
Page 15: Installation And Test
Raisecom Technology Co., Ltd 5. Installation and test 5.1. Inspect after Opening Please first check if the models and part numbers are in consistence, and also check if the equipments are damaged. 5.2. Preparation before Installation Carefully read this manual Prepare all kinds of the cable. -
Page 16: Troubleshooting
Raisecom Technology Co., Ltd 6. Troubleshooting If you have any problems during installation and usage, try to solve them by the following proposals. If the problem persists, please contact distributors for technical support. These following explanations and solutions of alarm for optical port and LOS alarm of V.35 tributary aim at alarm of local end. -
Page 17: Appendix A Introduction Of Cable Making
Raisecom Technology Co., Ltd 7. Appendix A Introduction of Cable Making A.1 V.35 Cable Making V.35 interface is compliant to V.35/ISO2593: DCE Connector Face – 34-pin Female connector. It can be connected with standard DTE cable. Please refer to Part 3.2.2 for wire sequence. - Page 18 Raisecom Technology Co., Ltd @2005 Raisecom Technology Co., Ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification.