[Slot In] - Panasonic PT-RQ32K Operating Instructions Manual

6) Press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
7) Press asqw to select [RESOLUTION].
f Select [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p],
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], [1920x1200p],
[2048x1080p], [2560x1600p], or [3840x2400p].
8) Press the <ENTER> button.
f The [VERTICAL SCAN FREQUENCY] screen is displayed.
9) Press qw to select [VERTICAL SCAN FREQUENCY].
f The setting is fixed to [30Hz] when [3840x2400p] is selected for [RESOLUTION].
f Select [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [2048x1080p] or [1920x1080p] is selected for
[RESOLUTION].
f Select [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
f Select [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
g [3840x2400p], [2048x1080p], [1920x1080p], [1920x1080i]
10) Press the <ENTER> button.
f The confirmation screen is displayed.
11) Press qw to select [OK], and press the <ENTER> button.
Note
f The settings in [RESOLUTION] and [VERTICAL SCAN FREQUENCY] are displayed in [EDID STATUS].
f The resolution and vertical scanning frequency settings may also be required on your computer or video device.
f After configuring settings, your computer or video device or the projector may be required to be turned off and on.
f A signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video
device.

[SLOT IN]

Set this item in accordance with the signal input to the input terminal of the installed Interface Board when the
optional Interface Board is installed in the slot.
The content that can be set varies depending on the structure of the installed Interface Board. It cannot be set if
no Interface Board is installed in the slots.
When the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed
Setting [HDMI LINK] in [SLOT IN] (HDMI input)
1) Press as to select [SLOT IN].
2) Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3) Press as to select [HDMI LINK], and press the <ENTER> button.
f The [HDMI LINK] screen is displayed.
4) Press as to select the setting.
[AUTO]
[SINGLE]
[DUAL]
*1
[DUAL/SINGLE]
*2
120 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Automatically selects the single link, the dual link, or the quad link.
Selects the quad link when the signal in the same format (such as resolution and timing) is input in
the four inputs of HDMI1, HDMI2, HDMI3, and HDMI4. Selects the dual link when the signal in the
same format is input in the HDMI1 input and the HDMI2 input, or the HDMI3 input and the HDMI4.
Quad link will be automatically selected when the optional Interface Board for HDMI 2 input (Model
No.: ET-MDNHM10) is installed in both of the slots.
Sets the HDMI1 input and the HDMI2 input, and the HDMI3 input and the HDMI4 input to single link.
(Factory default setting)
Sets the HDMI1 input and the HDMI2 input, or the HDMI3 input and the HDMI4 input to dual link.
Sets the HDMI1 input and the HDMI2 input to dual link, and the HDMI3 input and the HDMI4 input to
single link.