Panasonic PT-RQ32K Operating Instructions Manual page 212

Chapter 6 Maintenance — Light source/temperature/filter indicators
Temperature indicator <TEMP>
Indicator status
f Warm-up status
Lighting in red
f Internal temperature is high
(warning).
Blinking in red f Internal temperature is high (standby
(2 times) status).
Blinking in red
f The cooling fan has stopped.
(3 times)
*1 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level. When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is
set to [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F),
regardless of the altitude. When the Smoke Cut Filter is used, the operating environment temperature should be between 0 °C (32 °F) and 40 °C
(104 °F).
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level. When the Smoke Cut Filter is used, the projector
cannot be used at an altitude of 1 400 m (4 593') or higher above sea level.
*2 Maintenance of the Smoke Cut Filter is not possible. Replace with new one.
Note
f If the temperature indicator <TEMP> is still lit or blinking after taking the measures, ask your dealer for repair.
Filter indicator <FILTER>
r When the air filter unit/Replacement Filter Unit (Model No.: ET‑EMF330) is attached
Indicator status
f The filter is clogged.
f The runtime of the filter exceeds the
recommended time to replace the
Lighting in red
filter.
f The temperature around or outside
the projector is abnormally high.
f The air filter unit is not attached.
Blinking in red
f The Long Life Filter Unit or Smoke
Cut Filter is not attached.
*1 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level.
r When the Long Life Filter Unit (Model No.: ET-EMFU330) is attached
Indicator status
f The filter is clogged.
f The runtime of the filter exceeds the
recommended time to replace the
Lighting in red
filter.
*1
f The temperature around or outside
the projector is abnormally high.
Blinking in red f [FILTER TYPE]
*1 If the following two conditions are fulfilled, the recommended time to replace the filter is not set.
f The [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to anything other than [HIGH].
f The [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE] is set to [LONG LIFE].
*2 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level.
*3 [FILTER TYPE] can be set in the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE].
212 - ENGLISH
Status
f Wait five minutes when the power is turned on while the temperature is low
(approximately 0 °C (32 °F)).
f Install the projector in a location with the operating environment temperature
between 0 °C (32 °F) and 45 °C (113 °F)
f Remove any objects if they are blocking the air intake/exhaust port.
f Install the projector in a location with the operating environment temperature
between 0 °C (32 °F) and 45 °C (113 °F)
10 % and 80 % (no condensation).
f Perform maintenance
lights up. (x page 214)
f Turn the <MAIN POWER> switch to <OFF> (x page 69), and consult
your dealer.
Status
f Perform maintenance or replacement of the filter in the following cases.
(x page 214)
g The filter is dirty.
g The recommended time to replace the filter has been exceeded.
f Remove any objects if they are blocking the air intake/exhaust port.
f Do not use the projector at an altitude of 4 200 m (13 780')
above sea level.
f Attach the air filter unit/Replacement Filter Unit.
Status
f Perform maintenance or replacement of the filter in the following cases.
(x page 214)
g The filter is dirty.
g The recommended time to replace the filter has been exceeded.
f Remove any objects if they are blocking the air intake/exhaust port.
f Do not use the projector at an altitude of 4 200 m (13 780')
above sea level.
is set to [NORMAL]. f Set [FILTER TYPE]
*3
Solution
.
*1
, and ambient humidity between
*1
or replace the filter if the filter indicator <FILTER>
*2
Solution
Solution
to [LONG LIFE].
*3
or higher
*1
*1
or higher
*2