Page 1
Network Speed Dome Quick Start Guide UD06820B...
Page 2
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
Page 3
Network Speed Dome·Quick Start Guide USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Network Speed Dome·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Network Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Page 6
Network Speed Dome·Quick Start Guide Do not drop the speed dome or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid installation on vibrations surface or places subject to shock (ignorance can cause device damage). ...
Network Speed Dome·Quick Start Guide Table of Contents 1 Overview ...................... 1 1.1 Speed Dome Overview .................... 1 1.1.1 Overview of Type I Speed Dome ............... 1 1.1.2 Overview of Type II Speed Dome ..............1 1.1.3 Overview of Type III Speed Dome ..............2 1.1.4 Overview of Type IV Speed Dome ..............
Network Speed Dome·Quick Start Guide 1 Overview 1.1 Speed Dome Overview The network speed dome has five types. The figures below are for reference only, refer to the actual product as the standard. 1.1.1 Overview of Type I Speed Dome Figure 1-1 Overview of Type I Speed Dome Memory Card Slot Figure 1-2 Memory Card Slot...
Network Speed Dome·Quick Start Guide Figure 1-3 Overview of Type II Speed Dome Memory Card Slot Debug Reset Memory Card Slot Figure 1-4 Memory Card Slot 1.1.3 Overview of Type III Speed Dome CARD Memory Card Slot Figure 1-5 Overview of Type III Speed Dome...
Network Speed Dome·Quick Start Guide 1.1.4 Overview of Type IV Speed Dome Memory Card Slot Figure 1-6 Overview of Type IV Speed Dome 1.1.5 Overview of Type V Speed Dome Memory Card Slot Figure 1-7 Overview of Type V Speed Dome 1.2 Cable Interfaces The cable interfaces of the speed dome are shown in Figure 1-8.
Network Speed Dome·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Do not touch the bubble directly by hand. The image blurs otherwise. ...
Page 13
Network Speed Dome·Quick Start Guide Steps: 1. Loosen the two lock screws on both sides of the speed dome. Note: Do not remove the lock screws from the speed dome. Back Box Lens Cover Bubble Protective Foam Figure 2-2 Remove the Bubble Pull the bubble to separate it from the back box, and remove the protective accessories.
Page 14
Network Speed Dome·Quick Start Guide 3. If the speed dome supports PoE (Power over Ethernet) function, you can switch the PoE+ and Hi-PoE function for the speed dome. If PoE function is not supported, skip this step. Figure 2-5 PoE+ and Hi-PoE Switch Note: If you choose Hi-PoE, a Hi-PoE adapter must be connected.
Page 15
Network Speed Dome·Quick Start Guide 6. Install the bracket. 1). Drill four screw holes in the wall according to the holes on the bracket, and then insert four M8 expansion screws into the mounting holes. 2). Attach the gasket and the bracket to the wall by aligning the four screw holes on the bracket with four expansion screws on the wall.
Network Speed Dome·Quick Start Guide Lock Screw Lock Screw Figure 2-9 Install the Speed Dome to the Bracket 8. Remove the protective film on the bubble after the installation is finished.. 2.1.2 In-ceiling Mounting Note: In-ceiling mounting is only supported by indoor speed dome models of Type I. Before you start: ...
Page 17
Network Speed Dome·Quick Start Guide 5. Drill a hole on the ceiling according to the drill template (supplied). Note: ±2 mm of the circle diameter is tolerable. Φ 224 Unit: mm Figure 2-11 Drill a Hole on the Ceiling 6. Connect the cables. 7.
Network Speed Dome·Quick Start Guide 1). Attach the flange to the bubble and align the triangular notch of the trim ring with the arrow label on the in-ceiling bracket. 2). Firmly place the flange to the ceiling, and rotate the flange in the direction of the arrow to secure it.
Page 19
Network Speed Dome·Quick Start Guide 2). Remove the in-ceiling bracket as shown in Figure 2-16. Figure 2-16 Remove the Bracket 3). Install four bolts to the screw holes as shown in Figure 2-17. Figure 2-17 Install the bolts 2. Route the cables. The cables of speed dome can be routed either from the top or the side of the back box, as shown in Figure 2-18.
Page 20
Network Speed Dome·Quick Start Guide 3). Attach the bubble to the back box, and rotate clockwise to secure it. 4). Use the mounting base as a template to mark four screw holes onto the ceiling. 5). If you route cables from the top of the back box, mark the cable hole on the ceiling and drill a hole.
Network Speed Dome·Quick Start Guide 2.2 Installing Type II Speed Dome Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.
Page 22
Network Speed Dome·Quick Start Guide 3. Install the memory card. Debug Reset Memory Card Slot Memory Card Slot Open Cover Figure 2-23 Install the Memory Card. 4. Align the cuts on the bubble with the lock screws on the back box to reinstall the bubble.
Network Speed Dome·Quick Start Guide Lock Screw Figure 2-25 Install the Speed Dome to the Bracket 7. Remove the protective film on the bubble after the installation is finished. 2.3 Installing Type III Speed Dome Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.
Page 24
Network Speed Dome·Quick Start Guide Protective Sticker Figure 2-26 Remove Protective Sticker 2. Remove the cover on the back of speed dome as shown in Figure 2-27. Insert the memory card to the memory card slot and install the cover back. SD CARD Memory Card Slot Figure 2-27 Memory Card Slot...
Page 25
Network Speed Dome·Quick Start Guide Safety Rope Figure 2-28 Install the Safety Rope 5. Loosen the lock screws on the bracket. 6. Align the speed dome with bracket and rotate it counterclockwise or clockwise to the bracket tightly as shown in Figure 2-29. Figure 2-29 Install the Speed dome 7.
Network Speed Dome·Quick Start Guide Figure 2-30 Secure the Speed dome 8. Remove the protective film on the bubble after the installation is finished. 2.4 Installing Type IV Speed Dome Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket.
Page 27
Network Speed Dome·Quick Start Guide Protective Sticker Figure 2-31 Remove Protective Sticker 2. Remove the cover on the back of speed dome as shown in Figure 2-32. Insert the memory card to the memory card slot and install the cover back. Memory Card Slot Figure 2-32 Memory Card Slot 3.
Page 28
Network Speed Dome·Quick Start Guide Figure 2-34 Secure the Head Cover 5. Buckle the handle to the safety rope. Figure 2-35 Buckle the Handle 6. Hook the two ends of the safety rope to the speed dome back box and the bracket respectively.
Network Speed Dome·Quick Start Guide Figure 2-37 Route the Cables 9. Align the speed dome back box with the head cover. Use the wrench to tighten the lock screws to secure the speed dome and the bracket. Lock Screw Figure 2-38 Secure the Speed dome 10.
Page 30
Network Speed Dome·Quick Start Guide For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the speed dome and the accessories. ...
Page 31
Network Speed Dome·Quick Start Guide Figure 2-41 Secure the Bracket 4. Apply thread tape to the thread of the head cover and rotate the head cover to the bracket. Secure the head cover to the bracket with set screws (supplied). Figure 2-42 Secure the Head Cover 5.
Page 32
Network Speed Dome·Quick Start Guide Figure 2-44 Hang the Speed Dome 8. Route the cables through the head cover and bracket. Figure 2-45 Route the Cables 9. Align the speed dome back box with the head cover. Use the wrench to tighten the lock screws to secure the speed dome and the bracket.
Page 33
Network Speed Dome·Quick Start Guide Lock Screw Figure 2-46 Secure the Speed dome 10. Remove the protective film on the bubble after the installation is finished.
Network Speed Dome·Quick Start Guide 3 Setting the Speed Dome over the LAN Notes: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, strengthen your own protection.
Network Speed Dome·Quick Start Guide Activation via web browser, activation via SADP, and activation via client software are supported. We will take activation via SADP software and activation via web browser as examples to introduce the speed dome activation. 3.2.1 Activation via Web Browser Steps: 1.
Page 36
Network Speed Dome·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the speed dome. Steps: 1. Run the SADP software to search the online devices. 2.
Network Speed Dome·Quick Start Guide 3.3 Modifying the IP Address Purpose: To view and configure the speed dome via LAN (Local Area Network), you need to connect the network speed dome in the same subnet with your PC. Use the SADP software or client software to search and change the IP address of the device.
Page 38
Network Speed Dome·Quick Start Guide 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by SADP. Refer to the user manual of SADP for details.
Network Speed Dome·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version/Vista/Win7/Server 2003/Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024 × 768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 5 and above version and Google Chrome8 and above version Steps:...
Page 40
Network Speed Dome·Quick Start Guide Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above step 2 to step 4 to login. Note: For detailed instructions of further configuration, refer to the user manual of network speed dome.
Network Speed Dome·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the speed dome, receive alarm notification and so on. Note: Hik-Connect service is not supported by certain speed dome models. 5.1 Enable Hik-Connect Service on Speed Dome Purpose: Hik-Connect service should be enabled on your speed dome before using the service.
Network Speed Dome·Quick Start Guide 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the speed dome before enabling the service. Refer to Chapter 3.2 Activating the Speed Dome.
Network Speed Dome·Quick Start Guide 5.3 Adding Speed Dome to Hik-Connect Before you start: You need to enable the Hik-Connect service on speed dome before adding it to your Hik-Connect account. Refer to Chapter 5.1 Enable Hik-Connect Service on Speed Dome. Steps: 1.
Network Speed Dome·Quick Start Guide Note: For detailed information, refer to the user manual of the Hik-Connect app. 5.4 Initializing the Memory Card Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal.