Table of Contents
Advertisement
TURBO
HD 1080p Turret & Bullet
Camera
User Manual
UD01984B
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to models listed below.
Model
DS-2CE56D5T-IR3Z
DS-2CE16D5T-AIR3ZH
DS-2CE16D5T-AIR3Z
This manual may contain several technically incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
0100001060613
Advertisement
Table of Contents
Related Manuals for HIKVISION TurboHD
Summary of Contents for HIKVISION TurboHD
- Page 1 TURBO HD 1080p Turret & Bullet Camera User Manual UD01984B User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to models listed below. Model DS-2CE56D5T-IR3Z DS-2CE16D5T-AIR3ZH DS-2CE16D5T-AIR3Z...
- Page 2 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 4: Chapter 1 Introduction
extended period, please replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time. -
Page 5: Overview Of Bullet Camera
1.3 Overview of Bullet Camera Mounting Base Power Cabl (12 V DC) Main Body Video Cable (TVI) Video Cable (CVBS) Lens Figure 1. 2 Overview of Bullet Camera Chapter 2 Installation Before you start: Make sure that the device in the package is in good ... -
Page 6: Installation Of Bullet Camera
Figure 2. 2 Remove the Clip Plate 4. F x the mounting base to the ceiling with supplied screws. Note: In the supplied screw package, both self-tapping screws and expansion blots are contained. If the wall is cement, expansion blots are required ... -
Page 7: Chapter 3 Menu Operation
Figure 2. 5 Drill the Template 3. Route the cables to the cable hole and connect the corresponding cables, such as power cable, and video cable. 4. Fix the camera to the ceiling with the supplied screws. Figure 2. 6 Fix the Camera to the Ceiling Note: In the supplied screw package, both self-tapping ... -
Page 8: Video Out
Steps: 1. After the connection is done, power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. 2. Click PTZ Control to enter the PTZ Control Interface. 3. Call the camera menu by clicking button, or call preset No. -
Page 9: Smart Focus
3.4 SET UP 3.4.1 SMART FOCUS Automatically adjusts the camera focus according to the scene. You are allowed to set the value manually by clicking FOCUS+, FOCUS-, ZOOM+, ZOOM-.The value ranges from 0 to 99. The higher the value, the clearer the image is. - Page 10 AGC: It’s a form of amplification where the camera will automatically boost the image output signal to optimize the clarity of image in poor light conditions. You can set the AGC value from 0 to 15. The AGC is disabled if the value is set to 0.
- Page 11 1. GAIN MIDDLE 2. AREA 3. DEFAUT 4. RETURN Figure 3. 4 BLC HSBLC (High Suppress Back Light Compensation): Masks strong light sources that usually flare across a scene. This makes it possible to see the detail of the image that would normally be hidden.
-
Page 12: White Balance
3.4.6 WHITE BALANCE White balance is the white rendition function of the camera to adjust the color temperature according to the environment. It can remove the unrealistic color casts in the image. MANUAL, ATW (Auto-Tracking White Balance), AWC→SET are selectable. Manual: Allows you to adjust the white balance by customizing the BLUE and RED value, which range from 1 to 100. - Page 13 position and size of the area. Set the SENSITIVITY from 0 to 60. Set the MOTION VIEW as ON or OFF. MOTION 1. SELECT AREA 1 2. DISPLAY ON 3. SENSITIVITY ----|---- 30 4. MOTION VIEW ON 5. DEFAULT 6.
- Page 14 3.4.9 ADJUST In the Adjust sub-menu, you can configure the settings, including the sharpness, the image quality on monitor, and the LSC (lens shading compensation). Move the cursor to ADJUST and click Iris + to enter the adjust configuration interface. ADJUST --------|15 1.