Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2XE6222F-IS
Summary of Contents for HIKVISION DS-2XE6222F-IS
- Page 1 Explosion-Proof Network Bullet Camera Quick Start Guide UD04283B 0504051070109...
- Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
- Page 3 LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
- Page 4 Network Bullet Camera·Quick Start Guide APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information...
- Page 5 Network Bullet Camera·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU, the ATEX Directive 2014/34/EU.
- Page 6 Network Bullet Camera·Quick Start Guide IP Degree: IP68 (2m, 2h) Ex Standards: IEC 60079-0: 2011 EN 60079-0: 2012 IEC 60079-1: 2014 EN 60079-1: 2014 IEC 60079-31: 2013 EN 60079-31: 2014 Nameplate: Special Conditions for Safe Use: 1. Ambient Temperature: -30°C to +60°C. 2.
- Page 7 Network Bullet Camera·Quick Start Guide 5. Repair and overhaul shall comply with IEC 60079-19: latest version or its National equivalent. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
- Page 8 Network Bullet Camera·Quick Start Guide Warnings ● Grounding: The both internal and external earthing shall be connected reliably. Ground wire cross-sectional area of not less than the phase connector cross-sectional area level, at least 4 mm ● All the electrical operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations of the nation and region.
- Page 9 Network Bullet Camera·Quick Start Guide ● If the camera does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions ●...
- Page 10 Network Bullet Camera·Quick Start Guide ● To avoid heat accumulation, good ventilation is required for operating environment. ● To prevent accumulation of electrostatic charge, only damp cloth can be used during the cleaning. ● Keep the camera away from liquid while in use. ●...
-
Page 11: Table Of Contents
Network Bullet Camera·Quick Start Guide Table of Contents 1 Introduction .................. 11 Overview ............... 11 Model Description............11 2 Appearance Description ............... 13 Overview ............... 13 Cable Description ............14 3 Installation ..................16 4 Setting the Network Camera over the LAN ........20 Wiring ................ -
Page 12: Introduction
IP68 rating for ingress protection. Application Scenarios: oil industry, mine fields, chemical industry, port, grain processing industry, etc.. Model Description This manual is applicable to the following models: Table 1-1 Applicable Model List Model List DS-2XE6212F-IS DS-2XE6222F-IS DS-2XE6232F-IS DS-2XE6242F-IS DS-2XE6252F-IS DS-2XE6262F-IS DS-2XE6282F-IS... - Page 13 1: 1.3 MP 5: 5.0 MP 2: 2.0 MP 6: 6.0 MP 3: 3.0 MP 8: 8.0 MP 4: 4.0 MP Shape: 2: Bullet camera Professional Application type: E: Stainless Steel Explosion Proof For specialized application Hikvision front-end product Figure 1-1 Model Explanation...
-
Page 14: Appearance Description
Network Bullet Camera·Quick Start Guide 2 Appearance Description Overview Figure 2-1 Explosion-Proof Network Bullet Camera Overview (1) Figure 2-2 Explosion-Proof Network Bullet Camera Overview (2) -
Page 15: Cable Description
Network Bullet Camera·Quick Start Guide Cable Description Power Supply Alarm In/Out Network Figure 2-3 Overview of Cables Table 2-1 Description of Cables Cables Description Voltage: 100 VAC to 240 VAC Power Supply YELLOW/GREEN: for grounding YELLOW/BLUE: ALARM_IN1 WHITE/RED: ALARM_OUT1 Alarm In/Out YELLOW/ORANGE: ALARM_IN2 WHITE/PURPLE: ALARM_OUT2 YELLOW/BLACK: ALARM_GND... - Page 16 Network Bullet Camera·Quick Start Guide Cables Description Network For network communication Note: ALARM_IN1 and ALARM_OUT1 (ALARM_IN2 and ALARM_OUT2) should be used in pairs for alarm input and output.
-
Page 17: Installation
Network Bullet Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 100 VAC to 240 VAC, please make sure your power supply matches with your camera. - Page 18 Network Bullet Camera·Quick Start Guide Expansion Screws Figure 3-1 Install the Wall Mounting Bracket 2. Unscrew and remove the pedestal from the bracket. Screws Pedestal Screws Figure 3-2 Remove the Pedestal 3. Align the screw holes on the camera mounting base with those on the pedestal, and fix the camera to the pedestal with the supplied screws.
- Page 19 Network Bullet Camera·Quick Start Guide Safety Rope Mounting Base Pedestal Screws Figure 3-3 Fix the Camera to the Pedestal 4. Loosen the fixing screw, and adjust the panning position. Tighten the fixing screw after adjustment. Fixing Screw Pan: -45° to 45° Figure 3-4 Adjust Panning Position 5.
- Page 20 Network Bullet Camera·Quick Start Guide Tilt: -45° to 45° Figure 3-5 Secure the Camera to Wall Mounting Bracket 6. Secure the screws to finish installation.
-
Page 21: Setting The Network Camera Over The Lan
Network Bullet Camera·Quick Start Guide 4 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 22: Activating The Camera
Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. -
Page 23: Activation Via Sadp Software
Network Bullet Camera·Quick Start Guide Figure 4-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 24 Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2.
-
Page 25: Modifying The Ip Address
Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 26 Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 4-5 Modify the IP Address...
- Page 27 Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 6.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
-
Page 28: Accessing Via Web Browser
Network Bullet Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:... - Page 29 Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 5-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 30: Operating Via Hik-Connect App
Network Bullet Camera·Quick Start Guide 6 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so Note: Hik-Connect service is not supported by certain camera models. Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using... -
Page 31: Enable Hik-Connect Service Via Web Browser
Network Bullet Camera·Quick Start Guide Figure 6-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 6.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. - Page 32 Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 5. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 6-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4.
-
Page 33: Hik-Connect Setup
Network Bullet Camera·Quick Start Guide Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google Play 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before... - Page 34 Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 6-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.
-
Page 35: Initializing The Memory Card
Network Bullet Camera·Quick Start Guide Initializing the Memory Card Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.