Korg KROSS Operation Manual page 144

Appendices
Source is empty
Meaning: No data exists in the track that you specified as
the source.
• Specify a track that contains musical data.
Meaning: The export-source audio song does not contain
data.
• Specify an audio song that has been recorded.
Source sample is empty
Meaning: When using the pad sampler function, and
executing Insert or Paste, the source sample was empty.
• Execute the Copy command before you execute Insert or
Paste.
Source timbre is not available
Meaning: When executing the Copy Step Seq function, the
selected copy-source is a combination or song whose
"STEP" check box is not selected. In this case, the step
sequencer's pattern settings etc. will be copied, but the
program settings of timbre 16/track 16 will not be copied.
• Select the "STEP" check box of the copy-source
combination or song.
System warning
The internal memory has been corrupted, likely due to an
interruption of power while the system was writing/
saving data. This has been repaired and the affected Bank
has been initialized.
Meaning: A memory write procedure did not end normally,
perhaps because the power was turned off while processing
was still underway after you wrote a program or other data
into internal memory.
• The KROSS will automatically initialize itself in order to
repair the internal memory. This message will appear at
this time; press MENU(OK) button to close the dialog
box. In some cases, the preload bank data may be
temporarily initialized. As necessary, use the Global/
Media mode Load Preload/Demo Data command to load
the preload data into internal memory, or if you have
your own backup PCG, load it using Media mode.
T
There is no readable data
Meaning: Either the file size is 0 or the file does not contain
data that can be accessed by the load or open procedure.
Alternatively, the data is damaged etc., and cannot be loaded
or accessed.
The song exists, and will be initialized
Meaning: When executing the Sequencer mode Create New
Song function, you attempted to create a new song for a song
number that already exists. If you execute, the song will be
initialized, and a new song will be created and overwritten
onto it.
• If you don't want to initialize the currently-existing song,
specify a new song number.
The system has been idle for more than **** and will shut
down in:
You can change the Auto Power-Off setting on the
following page: GLOBAL - PREF 1
Meaning: If there has been no operation for the specified
length of time of time, the Auto Power Off function will
138
display a message informing you that the power will turn off
soon. The power will turn off when the countdown time
indication reaches zero.
• If you want to continue using the KROSS, press a key or
switch. Auto Power Off will be reset, and the same
message will appear when the specified length of time
has once again elapsed without any operation.
• If you want to disable this function or change the time
setting, go to the GLOBAL> PREF 1 page and set the
Auto Power-Off parameter. Use the Write Global Setting
function to save the setting.
This title is already loaded
• You attempted to load a EX-PCM option title that had
already been loaded.
Y
You can't undo last operation. Are you sure?
Meaning: Once you enter event editing (even if you leave
event editing without actually editing an event), it will no
longer be possible to execute Compare to listen to the
previous edit. If you wish to enter event editing, press the
MENU (OK) button. To cancel, press the FUNCTION
(CANCEL) button.
You can't undo this operation. Are you sure?
Meaning: When you exit recording or event editing in
Sequencer mode, the memory area for Undo (Compare
function) is not allocated. If you wish to keep the data that
was just recorded or edited, press the MENU (OK) button. If
you wish to return to the previous data (i.e., to delete the data
that was just recorded or edited), press the FUNCTION
(CANCEL) button.
Meaning: When editing in Sequencer mode, memory area
for Undo (Compare function) cannot be allocated. If you
wish to execute the edit, press the MENU (OK) button (It
will not be possible to undo your edit). If you decide not to
execute the edit, press the FUNCTION (CANCEL) button.
• In order to allocate memory area for Undo (Compare
function), delete unneeded data such as songs, or tracks.
We recommend that you data to media before you
execute the edit procedure.
You can use "Quick Setting" with [EXIT]+[ENTER]
Meaning: In the Audio In page of Program, Combination, or
Sequencer modes, this is shown at the bottom of the screen
when the G-SET check box On setting is selected. At this
time, the Audio In settings use the settings of the Global/
Media mode G-INPUT/CTRL>AUDIO IN page. To apply
these settings easily, hold down the EXIT button and press
the ENTER button to open the Audio In - Quick Setting
dialog box for G-SET.