GE UR Series C70 Instruction Manual page 610

FUSE FAILURE
see VT FUSE FAILURE
G
G.703 .............................................................3-30, 3-31, 3-32
GE TYPE IAC CURVES .................................................. 5-119
GROUND CURRENT METERING ...................................... 6-13
GROUND IOC
FlexLogic™ operands .................................................... 5-88
logic ............................................................................ 5-142
Modbus registers ...........................................................B-28
settings ....................................................................... 5-142
GROUND TIME OVERCURRENT
see entry for GROUND TOC
GROUND TOC
FlexLogic™ operands .................................................... 5-88
logic ............................................................................ 5-141
Modbus registers ...........................................................B-27
settings ....................................................................... 5-141
specifications ................................................................... 2-9
GROUPED ELEMENTS .................................................. 5-105
GSSE ................................................ 5-203, 5-204, 5-205, 6-5
H
HALF-DUPLEX .................................................................. B-1
HARMONIC CONTENT ..................................................... 6-15
HARMONICS
actual values ................................................................. 6-15
HARMONICS METERING
specifications ................................................................. 2-13
HTTP PROTOCOL ........................................................... 5-32
I
I2T CURVES .................................................................. 5-120
IAC CURVES ................................................................. 5-119
IEC 60870-5-104 PROTOCOL
interoperability document ................................................ D-1
Modbus registers ...........................................................B-19
settings ......................................................................... 5-32
IEC 61850 GOOSE ANALOGS
settings ....................................................................... 5-209
IEC 61850 GOOSE UINTEGERS
settings ....................................................................... 5-210
IEC 61850 PROTOCOL
device ID ..................................................................... 5-203
DNA2 assignments ...................................................... 5-205
error messages .............................................................. 7-11
Modbus registers .... B-42, B-43, B-44, B-45, B-46, B-47, B-58
remote device settings ................................................. 5-202
remote inputs .............................................................. 5-203
settings ......................................................................... 5-21
UserSt-1 bit pair .......................................................... 5-205
IEC CURVES ................................................................. 5-118
IED .................................................................................... 1-2
IED SETUP ........................................................................ 1-5
IEEE C37.94 COMMUNICATIONS ........................... 3-35, 3-37
IEEE CURVES ............................................................... 5-117
IMPORTANT CONCEPTS ................................................... 1-4
IN SERVICE INDICATOR .......................................... 1-17, 7-8
INCOMPATIBLE HARDWARE ERROR ................................ 7-9
INPUTS
iv
INDEX
C70 Capacitor Bank Protection and Control System
AC current ............................................................ 2-14, 5-65
AC voltage ............................................................ 2-14, 5-66
contact inputs .......................................... 2-14, 5-196, 5-218
dcmA inputs .......................................................... 2-14, 3-21
direct inputs ...................................................................2-14
IRIG-B .................................................................. 2-14, 3-26
remote inputs ................................. 2-14, 5-202, 5-203, 5-204
RTD inputs .....................................................................3-21
virtual .......................................................................... 5-198
INSPECTION CHECKLIST ................................................. 1-1
INSTALLATION
communications .............................................................3-23
CT inputs .............................................................. 3-11, 3-12
RS485 ...........................................................................3-24
settings ..........................................................................5-63
INSTANTANEOUS OVERCURRENT
see PHASE, GROUND, and NEUTRAL IOC entries
INTELLIGENT ELECTRONIC DEVICE ................................ 1-2
INTER-RELAY COMMUNICATIONS ..................................2-18
INTRODUCTION ................................................................ 1-2
INVERSE TIME UNDERVOLTAGE .................................. 5-144
IOC
see PHASE, GROUND, and NEUTRAL IOC entries
IP ADDRESS ....................................................................5-16
IRIG-B
connection .....................................................................3-26
error messages ..............................................................7-10
settings ..........................................................................5-36
specifications ........................................................ 2-14, 2-15
ISO-9000 REGISTRATION ................................................2-20
K
KEYPAD .................................................................. 1-17, 4-22
L
LAMPTEST ........................................................................ 7-7
LANGUAGE ......................................................................5-12
LATCHING OUTPUTS
application example ........................................... 5-200, 5-201
error messages ..............................................................7-11
settings ........................................................................ 5-199
specifications .................................................................2-15
LED INDICATORS ......................... 4-14, 4-15, 4-16, 4-21, 5-44
LED TEST
FlexLogic™ operand .......................................................5-92
settings ..........................................................................5-42
specifications .................................................................2-12
LINK POWER BUDGET .....................................................2-18
LOGIC GATES .................................................................5-94
LOST PASSWORD ...................................... 5-9, 5-10, 8-2, 8-3
M
MAINTENANCE COMMANDS ............................................. 7-7
MANUFACTURING DATE .................................................6-22
MEMORY MAP DATA FORMATS ..................................... B-61
MENU HEIRARCHY ................................................. 1-17, 4-25
MENU NAVIGATION ....................................... 1-17, 4-24, 4-25
METERING
conventions ............................................................6-9, 6-10
current ...........................................................................2-13
frequency .......................................................................2-13
GE Multilin