GE D30 Instruction Manual page 430

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE
IEC 61850 GOOSE messaging contains a number of con-
figurable parameters, all of which must be correct to
achieve the successful transfer of data. It is critical that the
configured datasets at the transmission and reception
devices are an exact match in terms of data structure, and
that the GOOSE addresses and name strings match
exactly. Manual configuration is possible, but third-party
C
substation configuration software may be used to automate
the process. The EnerVista UR Setupsoftware can produce
IEC 61850 ICD files and import IEC 61850 SCD files pro-
duced by a substation configurator (refer to the IEC 61850
IED Configuration section later in this appendix).
The following example illustrates the configuration required
to transfer IEC 61850 data items between two devices. The
general steps required for transmission configuration are:
1. Configure the transmission dataset.
2. Configure the GOOSE service settings.
3. Configure the data.
The general steps required for reception configuration are:
1. Configure the reception dataset.
2. Configure the GOOSE service settings.
3. Configure the data.
This example shows how to configure the transmission and
reception of three IEC 61850 data items: a single point sta-
tus value, its associated quality flags, and a floating point
analog value.
The following procedure illustrates the transmission config-
uration.
1. Configure the transmission dataset by making the fol-
lowing changes in the
CATION IEC 61850 PROTOCOL
CONFIGURATION
GOOSE CONFIGURABLE GOOSE 1
settings menu:
DATASET ITEMS
– Set to "GGIO1.ST.Ind1.q" to indicate quality
ITEM 1
flags for GGIO1 status indication 1.
– Set
ITEM 2
the status value for GGIO1 status indication 1.
The transmission dataset now contains a set of quality
flags and a single point status Boolean value. The
reception dataset on the receiving device must exactly
match this structure.
2. Configure the GOOSE service settings by making the
following changes in the
NICATION IEC 61850 PROTOCOL
CONFIGURATION
GOOSE CONFIGURABLE GOOSE 1
– Set
CONFIG GSE 1 FUNCTION
– Set
CONFIG GSE 1 ID
string (the default value is "GOOSEOut_1").
C-8
PRODUCT SETUP COMMUNI-
GSSE/GOOSE
TRANSMISSION CONFIGURABLE
CONFIG GSE 1
to "GGIO1.ST.Ind1.stVal" to indicate
PRODUCT SETUP
GSSE/GOOSE
TRANSMISSION CONFIGURABLE
settings menu:
to "Enabled".
to an appropriate descriptive
D30 Line Distance Relay
– Set
CONFIG GSE 1 DST MAC
(for example, 01 00 00 12 34 56).
– Set the
value of "4" is OK for this example.
– Set the
value is "0", but some switches may require this
value to be "1".
– Set the
ting represents the Ethertype application ID and
must match the configuration on the receiver (the
default value is "0").
– Set the
changes automatically as described in IEC 61850
part 7-2. For this example it can be left at its
default value.
3. Configure the data by making the following changes in
the
PRODUCT SETUP
61850 PROTOCOL
tings menu:
– Set
GGIO1 INDICATION 1
used to provide the status of GGIO1.ST.Ind1.stVal
(for example, a contact input, virtual input, a pro-
tection element status, etc.).
The D30 must be rebooted (control power removed and re-
applied) before these settings take effect.
The following procedure illustrates the reception configura-
tion.
1. Configure the reception dataset by making the follow-
ing changes in the
TION
CONFIGURATION
GOOSE CONFIGURABLE GOOSE 1
DATASET ITEMS
– Set
ITEM 1
flags for GGIO3 status indication 1.
– Set
ITEM 2
the status value for GGIO3 status indication 1.
The reception dataset now contains a set of quality
flags, a single point status Boolean value, and a float-
ing point analog value. This matches the transmission
dataset configuration above.
2. Configure the GOOSE service settings by making the
following changes in the
DEVICES
COMMU-
– Set
REMOTE DEVICE 1 ID
string
"GOOSEOut_1".
– Set
REMOTE DEVICE 1 ETYPE APPID
Ethertype application ID from the transmitting
device. This is "0" in the example above.
APPENDIX C
to a multicast address
CONFIG GSE 1 VLAN PRIORITY
value; the default
CONFIG GSE 1 VLAN ID
value. This set-
CONFIG GSE 1 ETYPE APPID
value. This value
CONFIG GSE 1 CONFREV
COMMUNICATION
GGIO1 STATUS CONFIGURATION
to a FlexLogic™ operand
PRODUCT SETUP
IEC 61850 PROTOCOL
RECEPTION CONFIGURABLE
CONFIG GSE 1
settings menu:
to "GGIO3.ST.Ind1.q" to indicate quality
to "GGIO3.ST.Ind1.stVal" to indicate
INPUTS/OUTPUTS
settings menu:
REMOTE DEVICE 1
to match the GOOSE ID
for the transmitting device.
to match the
; the default
IEC
set-
COMMUNICA-
GSSE/GOOSE
REMOTE
Enter
GE Multilin