Operation; Front Panel Leds; Video Input Leds; Audio Input Leds - Lightware HDMI-TPS-TX210 User Manual


  

4. Operation

4
O peration
This chapter is about the powering and operating of the device describing the
functions which are available by the front/rear controls:

Front Panel LEDs

Î

Front Panel Buttons

Î
Special Functions
Î
Rear Panel Status LEDs
Î
Software Control Modes
Î
HDMI-TPS-TX200 series – User's Manual
4.1. Front Panel LEDs
4.1.1. Video Input LEDs
VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
HDCP
Autoselect
DP IN HDMI IN HDMI IN DVI-D IN
OFF: The video source is not selected.
BLINKING: The video source is selected but signal is not
detected.
ON: The video source is selected and signal is detected.
4.1.2. Audio Input LEDs
VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
HDCP
Autoselect
DP IN HDMI IN HDMI IN DVI-D IN
OFF: The audio source is not selected.
BLINKING: The audio source is selected but no signal
is detected, regardless of the output mode
(e.g. DVI EDID is emulated on the port with
HDMI signal).
ON (with short pause): Audio source is selected, the audio is
embedded to the output video stream.
ON (continouosly): Audio source is selected, the port is active
but audio is not embedded in the video
stream (e.g. the output mode is DVI).
4.1.3. HDCP LED
VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
HDCP
Autoselect
DP IN HDMI IN HDMI IN DVI-D IN
OFF: Video output signal is not encrypted with HDCP.
ON: Video output signal is encrypted with HDCP.
4.1.4. Autoselect LED
VIDEO
HDCP
Autoselect
VIDEO AUDIO
RESET
AUDIO
VIDEO AUDIO SHOW
OFF:
5 AUDIO IN SELECT SELECT ME
BLINKING:
ON:
4.2. Front Panel Buttons
4.2.1. Video Select Button
VIDEO AUDIO
RESET
AUDIO
VIDEO AUDIO SHOW
VIDEO
5 AUDIO IN SELECT SELECT ME
HDCP
Autoselect
Only for SW4-TPS-TX240 model: desired video input can be selected
by the Video Select button from the front panel. The selection order of
the inputs is the following:
SW4-TPS-TX240:
4.2.2. Audio Select Button
VIDEO
HDCP
Autoselect
Desired audio input can be selected by the Audio Select button from the
VIDEO AUDIO
RESET
front panel. The selection order of the inputs depends on the model
AUDIO
VIDEO AUDIO SHOW
as follows:
5 AUDIO IN SELECT SELECT ME
HDMI-TPS-TX220:
DVI-HDCP-TPS-TX220:
DP-TPS-TX220:
SW4-TPS-TX240:
AUDIO VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
RESET
AUDIO
VIDEO AUDIO
DP IN HDMI IN HDMI IN DVI-D IN 5 AUDIO IN SELECT SELECT
Autoselect function is disabled.
Autoselect function is enabled, searching for
signal (the video input LEDs are also blinking).
Autoselect function is enabled, the active video
signal is found (the selected video input's LED is
also ON).
AUDIO VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
RESET
AUDIO
VIDEO AUDIO
DP IN HDMI IN HDMI IN DVI-D IN 5 AUDIO IN SELECT SELECT
DP HDMI 1 HDMI 2
Autoselect
AUDIO VIDEO AUDIO VIDEO AUDIO VIDEO AUDIO
RESET
AUDIO
VIDEO AUDIO
5
DP IN HDMI IN HDMI IN DVI-D IN AUDIO IN SELECT SELECT
Embedded digital audio Analog audio
21
SHOW
ME
SHOW
ME
DVI-D
SHOW
ME